ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
A 5-20(20a) receptacle is legal on a 15a circuit?
by libellis - 10/10/21 12:46 PM
GFCI's pops in large numbers
by dsk - 10/07/21 03:46 PM
Backup Generator Done Right
by timmp - 10/06/21 02:07 PM
How's all our Non-US folks doing?
by dsk - 09/30/21 05:06 AM
Well I am back to stay (nearly 6 years)
by Bill Addiss - 09/26/21 11:09 PM
New in the Gallery:
240/208 to a house
240/208 to a house
by wa2ise, October 9
Now you know.
Now you know.
by Tom_Horne, September 7
Who's Online Now
0 members (), 5 guests, and 23 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
#221544 08/07/21 09:03 PM
Joined: Aug 2021
Posts: 1
K
koiman Offline OP
New Member
First let me say I am not a professional. But I need the help of a professional. I have an old Emerson Motor picture attached belonging to a vintage craftsman Jointer. My quandary is what wire of the cord goes to what Terminal? there are four terminals. I opened up the motor and tested every thing for continuity and here is what I have found. Terminals #1 and #3 are connected to the run winding. Neither of them test for continuity with either of the other wires? The wire from #2 goes to the start winding, capacitor and ends at centrifugal switch ( bar underneath switch) Term. #4 connects directly to the base part of the switch. All the diagrams I have looked at show the run winding circuit being in parallel with the start winding circuit. But if it is shouldn't I find continuity with the other circuit this is where I am confused. Crude diagram attached. I do understand the basics of how this motor operates but I am missing some thing here. Any knowledge any one could give me would be welcome. Also mainly which terminals would the hot and neutral be connected to. If there's any other testing I can do? Thanks Much

Attached Images
planer3.jpg planer wiring.jpg planer motor3.jpg
Joined: Dec 2005
Posts: 866
Likes: 4
R
Member
If you test for continuity through a capacitor that won't work with an Ohmmeter.
To check the other (start) winding for continuity you need to bridge across the capacitor and see what readings you get.
Normally a run winding has a thicker gauge wire, and will have a lower ohm reading. (e.g. 12 Ohms)
A start winding has a thinner gauge of wire, and will have a higher ohm reading (e.g. 17 Ohms)
Try to do an insulation check first, and see if there is no winding short to earth (motor frame).
Check the centrifugal switch if it works. (should be closed at standstill).
That wire insulation looks brittle and may need some additional sleeving.

To do a simple testrun and see if the motor works. Connect 1 and 3 to a 110 volts supply, the earth to the exposed motor frame (safety), the motor should hum, it may sometimes even start without a start winding energized.
Switch power off !
Give the pulley a push with a stick or wrap a string around the pulley, before energizing. Pull the string, so the pulley and armature rotate, then energize the motor and see if it works.

Now test the motor with start winding.

If the start winding and capacitor is ok. connect 1 and 2 together on Active, or Phase and 3 and 4 together on the Neutral.
The motor should start and run, centrifugal switch should switch start winding off.
To change rotation of the motor, connect 1 and 4 to Active and 2 and 3 to Neutral.
That flips over the start field and the motor will run the other way

Hope it helps.

Last edited by RODALCO; 08/28/21 01:35 AM. Reason: typo's

The product of rotation, excitation and flux produces electricty.

Link Copied to Clipboard
Featured:

Tools for Electricians
Tools for Electricians
 

* * * * * * *

2020 Master Electrician Exam Preparation Combos
2020 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
MarkC10
MarkC10
CA, Inland Empire
Posts: 43
Joined: September 2013
Top Posters(30 Days)
dsk 5
Popular Topics(Views)
284,541 Are you busy
217,274 Re: Forum
203,620 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.5