ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Shout Box
Recent Posts
AreMetal Ladders Ever OK For Electrical Work?
by HotLine1. 01/22/18 07:31 PM
Photocell
by twh. 01/22/18 05:06 PM
VDE 0100 to introduce AFCIs
by sparky. 01/20/18 05:09 PM
MRI LED lights dimmer control replacement - wow!
by Potseal. 01/19/18 08:52 PM
New in the Gallery:
Housebilding DIY wiring
SE cable question
Who's Online Now
0 registered members (), 24 guests, and 12 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
Guess who Wired This? #112647
08/19/01 10:43 AM
08/19/01 10:43 AM
Admin  Offline
OP
Administrator
Member
Joined: Oct 2000
Posts: 3,482
NY, USA
[Linked Image]

[Linked Image]

[Linked Image]

3 Guesses who wired this Furnace?
(hint, not an Electrician)

Bill

Tools for Electricians:
Re: Guess who Wired This? #112648
08/19/01 03:30 PM
08/19/01 03:30 PM
Joe Tedesco  Offline
Member
Joined: Oct 2000
Posts: 2,749
Boston, Massachusetts USA
1. The mailman?

2. The garbage man?

3. The carpenter?



[This message has been edited by Joe Tedesco (edited 08-19-2001).]


Joe Tedesco, NEC Consultant
Re: Guess who Wired This? #112649
08/19/01 06:03 PM
08/19/01 06:03 PM
sparky66wv  Offline
Member
Joined: Nov 2000
Posts: 2,236
West Virginia
Excellent Grounding Continuity though!


-Virgil
Residential/Commercial Inspector
5 Star Inspections
Member IAEI
Re: Guess who Wired This? #112650
08/19/01 06:36 PM
08/19/01 06:36 PM
Bill Addiss  Offline
Member
Joined: Oct 2000
Posts: 3,890
NY, USA
Joe,

It was the Plumber!
I thought you were a better guesser than that! [Linked Image]

Bill

Re: Guess who Wired This? #112651
08/19/01 07:04 PM
08/19/01 07:04 PM
G
George Corron  Offline
Member
Joined: May 2001
Posts: 717
Lorton, Va USA
And you DIDN'T get a picture of the bend ??????

Re: Guess who Wired This? #112652
08/19/01 07:27 PM
08/19/01 07:27 PM
sparky66wv  Offline
Member
Joined: Nov 2000
Posts: 2,236
West Virginia
The handy box has four empty KO's, so there's room for four more cables, right?

[Linked Image]


-Virgil
Residential/Commercial Inspector
5 Star Inspections
Member IAEI
Re: Guess who Wired This? #112653
08/19/01 08:05 PM
08/19/01 08:05 PM
Joe Tedesco  Offline
Member
Joined: Oct 2000
Posts: 2,749
Boston, Massachusetts USA
Would you reconsider the use of the copper pipe, since it maybe of the type that will comply with rules in Article 680 where "brass or other approved corrosion-resistant metal" is allowed to be used for the wiring methods for some systems.

Search for the term "conduit" and look at the many entries in that Article


Joe Tedesco, NEC Consultant
Re: Guess who Wired This? #112654
08/21/01 06:54 AM
08/21/01 06:54 AM
electure  Offline

Member
Joined: Dec 2000
Posts: 4,264
Fullerton, CA USA
Even plumbers are required to strap their pipe!
There's only one strap visible in this whole mess!

Re: Guess who Wired This? #112655
08/21/01 07:41 AM
08/21/01 07:41 AM
Bill Addiss  Offline
Member
Joined: Oct 2000
Posts: 3,890
NY, USA
George,

I think the bend was OK,
What I would've liked to check was if the cuts were made with a pipe-cutter and if there was a sharp edge inside.

Joe,

You mean this might be OK?
what about the size itself? This conduit is a bit smaller than our Electrical conduit and doesn't fit in the connectors quite right.

Bill

Re: Guess who Wired This? #112656
08/21/01 10:53 AM
08/21/01 10:53 AM
Joe Tedesco  Offline
Member
Joined: Oct 2000
Posts: 2,749
Boston, Massachusetts USA
Bill:

Naturally, I would not permit the material you show, but would permit the same material if it was equal in the ID and had threads as any of the Table 4, Chapter 9 wiring methods.


Joe Tedesco, NEC Consultant
Page 1 of 3 1 2 3

Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
RH1
RH1
California
Posts: 22
Joined: August 2009
Show All Member Profiles 
Top Posters(30 Days)
Admin 21
sparky 15
Potseal 15
Popular Topics(Views)
243,602 Are you busy
180,416 Re: Forum
170,873 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Release build 20180101)
Page Time: 0.027s Queries: 16 (0.004s) Memory: 1.0245 MB (Peak: 1.2037 MB) Zlib enabled. Server Time: 2018-01-23 21:14:43 UTC