ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat Box
Recent Posts
Anybody Remember this?
by Bill Addiss - 08/17/19 09:07 PM
Fuse blower plug?
by Bill Addiss - 08/17/19 09:01 PM
100 year old Light Bulb
by Bill Addiss - 08/17/19 11:44 AM
1897 paper on 110-220 incandescent lamps
by ghost307 - 08/15/19 10:31 AM
Forum Updates Coming Soon.
by Admin - 08/08/19 11:50 PM
New in the Gallery:
What is this for?
Plug terminals
Who's Online Now
0 registered members (), 10 guests, and 12 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Stallcup Question #51060 04/20/05 12:36 PM
Joined: May 2001
Posts: 717
G
George Corron Offline OP
Member
Alright, a little help here.
Stallcup has, in one of his books, a question about cable bending in "L" "S", and "Z" configurations.

One of my former students now teaches code, and one of his was recently asked a question about cable bending radius based on the above configurations.

I've only been able to give it a few minutes but danged if I can find ANY code reference to it. I will look in Jim's books tonight, but anyone on this forum got a clue?

Work Gear for Electricians and the Trades
Re: Stallcup Question #51061 04/20/05 05:07 PM
Joined: Jan 2001
Posts: 1,044
Tom Offline
Member
I don't know of any bending radius requirements for an individual conductor. Every cable article (MC, NM, etc) does have a limit on the minimum radius since you wouldn't be able to observe any damage done to the enclosed conducxtors.


Few things are harder to put up with than the annoyance of a good example.
Re: Stallcup Question #51062 04/20/05 05:12 PM
Joined: Mar 2001
Posts: 2,056
R
Redsy Offline
Member
George,

Try the commentary in the '02 Handbook on page 297.

Re: Stallcup Question #51063 04/21/05 12:52 PM
Joined: Jun 2003
Posts: 1,143
D
DougW Offline
Member
Of course, I'm at the Fire Station with no Codebook, but IIRC aren't those different methods of routing a cable in a box to support it vertically?

Re: Stallcup Question #51064 04/21/05 07:33 PM
Joined: May 2001
Posts: 717
G
George Corron Offline OP
Member
Thanks Redsy,
After looking at it, I really don't think that's it. The old vertical support methods would fit, but the question was specifically about terminations. I'm going to have to look in Jim's old "Designing Electrical Systems" to see if there's a clue in there.

Thanks for your help guys, I'll let you know if I find anything concrete in case you run across it.

Re: Stallcup Question #51065 04/21/05 11:04 PM
Joined: Aug 2004
Posts: 34
H
highkvoltage Offline
Member
Flexible Conduit
Chapter 9 Table 2 Column Other bends.

AC Cable 320.24


Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
richard
richard
L.I. New York
Posts: 99
Joined: August 2003
Show All Member Profiles 
Top Posters(30 Days)
Admin 16
GeneSF 8
Popular Topics(Views)
257,828 Are you busy
193,565 Re: Forum
183,204 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.3