ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Shout Box
Recent Posts
Don't you buy this stuff
by HotLine1. 05/22/18 03:52 PM
Furnace igniter leaking noise to stereo
by Haligan. 05/21/18 03:28 PM
480 Delta
by ghost307. 05/21/18 10:38 AM
turning down possible problem customer
by HotLine1. 05/21/18 07:53 AM
electircal ageing test on IPC
by HotLine1. 05/14/18 09:42 AM
New in the Gallery:
Plug terminals
Housebilding DIY wiring
Who's Online Now
0 registered members (), 4 guests, and 8 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Inline adapter for single phase power monitors ? #207828
11/29/12 04:45 PM
11/29/12 04:45 PM
L
LarryC  Offline OP
Member
Joined: Jul 2004
Posts: 783
Winchester, NH, US
Does anyone know of a off the shelf breakout assembly to connect a power analyzer to? I need to safely measure electical parameters for a system that is plugged into a NEMA 5-20 receptacle.

Before I go and build a couple of nice little breakout boxes, I figured why re-invent the wheel. I am looking for something I can plug inline and connect the power analyzer to it.

I am using the IEC 320 high and standard power connectors.

Thanks.

Work Gear for Electricians and the Trades
Re: Inline adapter for single phase power monitors ? [Re: LarryC] #207830
11/29/12 08:01 PM
11/29/12 08:01 PM
G
gfretwell  Offline

Member
Joined: Jul 2004
Posts: 9,223
Estero,Fl,usa
If this is a duplex receptacle, what is in the other side? You might just need a test cord with a cap on it.


Greg Fretwell
Re: Inline adapter for single phase power monitors ? [Re: gfretwell] #207832
11/29/12 11:13 PM
11/29/12 11:13 PM
L
LarryC  Offline OP
Member
Joined: Jul 2004
Posts: 783
Winchester, NH, US
I am looking for a prebuilt "box" that has male and female IEC 320 connectors, an insulated wire to clamp the current probe onto, and finger safe shrouded female banana jacks to connect the voltage leads.

I will be making multiple measurements inside the system under test, and I did not want to mess around with a hacked up line cord.

I can roll my own box, but I figured if someone else already built one, why reinvent the wheel.

Re: Inline adapter for single phase power monitors ? [Re: LarryC] #207833
11/29/12 11:31 PM
11/29/12 11:31 PM
G
gfretwell  Offline

Member
Joined: Jul 2004
Posts: 9,223
Estero,Fl,usa
I made up my own C13/14 cable for my Dranitz because I never saw a commercial one but that was a while ago. I will wait to see if Scott or anyone has seen one.


Greg Fretwell
Re: Inline adapter for single phase power monitors ? [Re: LarryC] #207837
11/30/12 01:02 AM
11/30/12 01:02 AM
Scott35  Offline

Broom Pusher and
Member
Joined: Oct 2000
Posts: 2,708
Anaheim, CA. USA
I have seen / used several of these, however they all had NEMA Devices; Locking types being the most common
(i.e.: L5-20 through L22-30).

IMO, there _SHOULD_ be similar Test Equipment with IEC 320 Panel Mounted Devices.

If nothing is available in the IEC Panel Mount Schemes (NEMA only), you could makeup Two Gender-Bender type Patch Cords, each with IEC-to-NEMA Devices:
(1) IEC Plug - NEMA Receptacle
(1) NEMA Plug - IEC Receptacle

Sorry for not having any helpful information, but I will ask around.

-- Scott (EE)



Scott " 35 " Thompson
Just Say NO To Green Eggs And Ham!
Re: Inline adapter for single phase power monitors ? [Re: Scott35] #207844
11/30/12 01:25 PM
11/30/12 01:25 PM
L
LarryC  Offline OP
Member
Joined: Jul 2004
Posts: 783
Winchester, NH, US
I am looking at making up a small box with male / female cord whips, EZ Hook 9408 (dual shrouded banana jacks), and a insulated wire for the current clamp.

Does anyone have a specific P/N for an insulated handle looking thing to hook the amp clamp onto?

Re: Inline adapter for single phase power monitors ? [Re: LarryC] #207845
11/30/12 02:29 PM
11/30/12 02:29 PM
G
gfretwell  Offline

Member
Joined: Jul 2004
Posts: 9,223
Estero,Fl,usa
A few inches of Carflex with right angle connectors?


Greg Fretwell
Re: Inline adapter for single phase power monitors ? [Re: gfretwell] #207846
11/30/12 04:08 PM
11/30/12 04:08 PM
L
LarryC  Offline OP
Member
Joined: Jul 2004
Posts: 783
Winchester, NH, US
Gfretwell: Neat idea.

Scott35: Do you have Manufacturers and P/Ns for the adapters you have used? Perhaps I can buy one of those and modify it for my needs.

Re: Inline adapter for single phase power monitors ? [Re: LarryC] #208106
12/27/12 06:09 AM
12/27/12 06:09 AM
Scott35  Offline

Broom Pusher and
Member
Joined: Oct 2000
Posts: 2,708
Anaheim, CA. USA
Larry,

Sorry, but I do not have any Manufacturers to quote.

I will poke around the Net (Google) and let you know what I find.

-- Scott (EE)


Scott " 35 " Thompson
Just Say NO To Green Eggs And Ham!
Re: Inline adapter for single phase power monitors ? [Re: Scott35] #208116
12/27/12 10:43 PM
12/27/12 10:43 PM
L
LarryC  Offline OP
Member
Joined: Jul 2004
Posts: 783
Winchester, NH, US
Thanks. The project is heating back up.

I am seriously considering using a boxed receptacle inline with a "de-jacketed" power cable to safely provide a voltage measuring point along with the access for the current clamp. I'll use a chopped line cord to connect the voltage leads.

Page 1 of 2 1 2

Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
SafetyWired
SafetyWired
Pa, USA
Posts: 44
Joined: July 2013
Show All Member Profiles 
Top Posters(30 Days)
twh 12
Popular Topics(Views)
246,870 Are you busy
184,220 Re: Forum
173,459 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Release build 20180101)
Page Time: 0.022s Queries: 16 (0.003s) Memory: 1.0260 MB (Peak: 1.2105 MB) Zlib enabled. Server Time: 2018-05-22 23:39:46 UTC