ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Recent Posts
Lowes Selling this fan
by timmp - 07/25/21 10:58 PM
How's all our Non-US folks doing?
by djk - 07/23/21 09:13 PM
Switched Receptacles -Top or Bottom?
by donles - 07/23/21 10:51 AM
Do You Travel?
by Bill Addiss - 07/20/21 04:26 PM
Backup Generator Done Right
by timmp - 07/18/21 12:20 PM
New in the Gallery:
February, North East Indiana
February, North East Indiana
by timmp, July 25
Red Green would be proud
Red Green would be proud
by timmp, July 25
Who's Online Now
0 members (), 20 guests, and 14 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
#115804 12/23/03 06:39 PM
Joined: Oct 2000
Posts: 3,661
Likes: 1
Admin Offline OP
[Linked Image]

[Linked Image]
Here are two pictures of a piece of equipment that came over from another one of our buildings. It's an air dryer for compressed air. As you can see, they didn't want to use fuses, so they came up with a more "practical" idea!!! We had the company photographer take these pictures so we could have this mess documented in case there were any problems with the equipment.

I, as well as my co-workers love your forums on code violations. It's unbelievable what some people will do.

-Joe Martell

#115805 12/23/03 09:39 PM
Joined: Apr 2002
Posts: 2,527
Those clips have to be stretched or squeezed...9/16-inch copper tubing doesn't exist.

But, there is a correct product for the job—Bussmann "NTN-R30" for 30A 250V swithces.

[This message has been edited by Bjarney (edited 12-23-2003).]

#115806 12/23/03 10:42 PM
Joined: Dec 2003
Posts: 2
Junior Member
Let me make it clear that this is how the equiment came over from one of our other buildings and this is what we found when we came to do the electrical install. This is NOT how we left it. We wanted it documented that the equipment arrived like this, hence we had the company photographer take pictures.
We did the install and corrected any and all pre-existing violations, including changing the disconnect and installing the proper size fuses.
My point was how they could have run this equipment like this in our other building located in New Jersey.

#115807 12/23/03 11:17 PM
Joined: Nov 2003
Posts: 269
I see a red, blue, black and white wire entering the top of the disco, but what appears to be one white wire leaving the short piece of EMT. Am I missing something? [Linked Image]

#115808 12/23/03 11:38 PM
Joined: Jul 2002
Posts: 8,407
Likes: 2
That White wire wouldn't be a neutral would it?.
That terminal block at the bottom of the disconnect looks like it's segregated from the metal panel, would this be where the neutral joins with another wire that loops down to the receptacle below?. [Linked Image]

#115809 12/24/03 04:07 AM
Joined: Jul 2003
Posts: 394
It looks like kind of a sleazy setup overall but was a fused disconnect required where the equipment was previously installed?

#115810 12/24/03 12:13 PM
Joined: Aug 2001
Posts: 7,520
I see a red, blue, black and white wire entering the top of the disco, but what appears to be one white wire leaving the short piece of EMT. Am I missing something?

Looks to me as though the receptacle below the disco is tapped from the red phase and the main equipment is wired 208V delta with no neutral.

#115811 12/24/03 07:19 PM
Joined: Sep 2003
Posts: 123
I've seen this done alot out here in the land of OZ. Usually on a roof mounted air handler. Found out that it was a crew run by the guy who is now my boss. He used to do this so that they could keep the units running and find the short when the wire burned up.

BTW, I am looking for other employment.

#115812 12/26/03 08:54 AM
Joined: Dec 2000
Posts: 4,287
Per Paul
>The receptacle below the disco is tapped >from the red phase.
I'd agree, but what's the little box in between the disco and the recp?
Does that contain a 5 amp Edison base fuse for the recp?

#115813 12/26/03 04:20 PM
Joined: Apr 2002
Posts: 2,527
The middle box looks like a Bussmann SOU listed at

Page 1 of 2 1 2

Link Copied to Clipboard

Tools for Electricians
Tools for Electricians

* * * * * * *

2020 Master Electrician Exam Preparation Combos
2020 NEC Electrician
Exam Prep Combos:
Master / Journeyman


Member Spotlight
Belmond Iowa US
Posts: 44
Joined: August 2005
Top Posters(30 Days)
timmp 7
Rachel 4
Popular Topics(Views)
281,451 Are you busy
215,094 Re: Forum
201,958 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.5