ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Shout Box
Recent Posts
Board tester power supply?
by JoeTestingEngr. 10/13/18 12:14 AM
Voltage sag
by Trumpy. 10/12/18 06:59 PM
220/230/240V 60Hz Systems
by Trumpy. 10/12/18 06:50 PM
Linear Power Supply Quits Under Load
by JoeTestingEngr. 10/10/18 08:47 PM
License to survive
by HotLine1. 10/02/18 08:52 PM
New in the Gallery:
What is this for?
Plug terminals
Who's Online Now
0 registered members (), 13 guests, and 29 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Two for One! #103443
08/01/02 05:34 PM
08/01/02 05:34 PM
Joe Tedesco  Offline OP
Member
Joined: Oct 2000
Posts: 2,749
Boston, Massachusetts USA
[Linked Image]

Hey!

Cite the rules that are violated here!


Joe Tedesco, NEC Consultant
2017 / 2014 NEC & Related Books and Study Guides
Re: Two for One! #103444
08/01/02 06:34 PM
08/01/02 06:34 PM
R
Randy Barnett  Offline
Junior Member
Joined: Apr 2002
Posts: 4
Loveland CO
Caught you Joe -- using one of my pictures, eh? Go ahead anytime!

Say, don't blame the electrician on this one. This work was done on an Air Force base after the final electrical inspection was completed. The irrigation contractor needed to get 120V to his irrigation box on the outside of the building (upper right). So, he found a way to get it done (ouch!).

When we saw the flexible conduit going into that elbow, we had to get a key to open the door and this picture is what we found!

Re: Two for One! #103445
08/02/02 07:43 AM
08/02/02 07:43 AM
Joe Tedesco  Offline OP
Member
Joined: Oct 2000
Posts: 2,749
Boston, Massachusetts USA
Randy:

Whew! I was really worried, and didn't want any legal problems.

I too have many pictures and many people use them during their classes. I have no problem with that because I am the only one who has "the rest of the story"

Do you have any more pictures to share?

Quote
Say, don't blame the electrician on this one. This work was done on an Air Force base after the final electrical Inspection was completed. The irrigation contractor needed to get 120V to his irrigation box on the outside of the building (upper right). So, he found a way to get it done (ouch!).




[This message has been edited by Joe Tedesco (edited 08-02-2002).]


Joe Tedesco, NEC Consultant
Re: Two for One! #103446
08/02/02 10:44 AM
08/02/02 10:44 AM
W
wirewiz  Offline
Member
Joined: Jan 2002
Posts: 122
WA.
Violations:
110-2. Approval. The conductors and equipment required or permited by this code shall be acceptable only if approved.

547-13. Bends- How Made. Bends of rigid nonmetallic conduit shall be made so that the conduit will not be damaged and the internal diamater of the conduit will not be effectively reduced. Field bends shall be made only with bending equipment identified for the purpose, and the radius of the inner edge of such bends shall not be less than shown in table 346-10.

347-8. (a) Securely Fastened Each rigid nonmetallic conduit shall be securely fastened within 3 ft of each outlet box, junction box, device box, conduit body, or other conduit termination. Conduit listed for securing at other than 3 ft shall be permited to be installed in accordance with the listing.

What did I miss?
Wirewiz

Re: Two for One! #103447
08/10/02 09:59 AM
08/10/02 09:59 AM
Joe Tedesco  Offline OP
Member
Joined: Oct 2000
Posts: 2,749
Boston, Massachusetts USA
wirewiz:

Good, and from the 1999 NEC, just change 547-13 to 347-13.


Joe Tedesco, NEC Consultant

Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
HappyElectrician
HappyElectrician
Penn USA
Posts: 31
Joined: December 2011
Show All Member Profiles 
Top Posters(30 Days)
sparky 11
Popular Topics(Views)
250,251 Are you busy
187,909 Re: Forum
177,439 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Release build 20180101)
Page Time: 0.017s Queries: 14 (0.004s) Memory: 0.9686 MB (Peak: 1.1092 MB) Zlib enabled. Server Time: 2018-10-15 17:16:34 UTC