ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Increasing demand factors in residential
by tortuga - 03/28/24 05:57 PM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
Cordless Tools: The Obvious Question
by renosteinke - 03/14/24 08:05 PM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
0 members (), 265 guests, and 15 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
#53410 06/23/05 11:14 PM
Joined: Mar 2005
Posts: 24
A
Member
Is it true that T8 fluorescent bulbs have more light output than a T12 of the same wattage? Also I was told that if one T8 bulb burns out then the others will stay on as compared to a T12 where if one bulb burns out then they all go out. Wouldnt this depend on the type of ballast that you are using?

#53411 06/24/05 04:31 AM
Joined: Jan 2003
Posts: 4,391
I
Moderator
We are currently involved with replacing about 5000 ballasts in a warehouse.

The originals fixtures where 2 lamp 8' high output T-12s, we convert them to 4 lamp 4' T-8s and the light output is much higher.

As far as the ballasts you need T-8 ballasts for T-8 lamps.

Also available are 4' T-5 high output lamps which with 4 of them can replace a 400 watt HID fixture.


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#53412 06/24/05 07:28 AM
Joined: Oct 2004
Posts: 265
D
Member
When T8s fail, usually only that bulb will go bad, if you see 2 T8s out, its almost always a bad ballast.

T12s on the other hand can have a single lamp go out or both lamps. I think it depends on how the lamp fails internally. Also, if you remove a T12 from a 2 lamp ballast, it will shut off the other light, a T8 ballast will power a single lamp with no problem.

I think you are correct that this is more to do with electronic vs magnetic ballasts.

#53413 06/25/05 01:33 PM
Joined: Feb 2003
Posts: 27
W
Member
T8 4 bulb 2 by 4 troffer luminaire becomes a lot lighter than the T12 so light if installed in suspended ceiling and it is not fasten properly you could push the whole luminaire out of the ceiling grid. The ballast only requires 1 not 2 and they weigh one fourth of ther T12 ballast. Never checked lumens but heard from customers it is alot brighter.


William Runkle
#53414 06/25/05 01:36 PM
Joined: Jan 2003
Posts: 4,391
I
Moderator
Quote
I think you are correct that this is more to do with electronic vs magnetic ballasts.

I have never seen a magnetic ballast for a T-8.

Is there such a thing?


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#53415 06/25/05 08:21 PM
Joined: Oct 2004
Posts: 72
B
Member
Hay what does the (T) stand for in T5 T8 and T12

#53416 06/25/05 08:24 PM
Joined: Jan 2003
Posts: 4,391
I
Moderator
T = Tube or Tubular.

FYI the numbers represent 8ths of an inch.

A T-5 is 5/8" in diameter, a T-8 is 8/8" or 1" in diameter.


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#53417 06/25/05 09:36 PM
Joined: Sep 2001
Posts: 806
N
Member
The "eighths of an inch diameter" thing goes back to the early days of lamps and radio tubes, and lives on to this day. Even LEDs are commonly specified this way (T1-3/4 is a common package).

The number of eighths in the diameter is also the basis of the NEMA motor frame designations, AFAIK. For example, a 56 frame motor was originally 56/8ths " in diameter, or 7". As motors have improved, they have gotten a bit smaller, but the numbers still provide a rough idea of size.

#53418 06/25/05 11:04 PM
Joined: Jan 2003
Posts: 4,391
I
Moderator
Thanks NJ, I did not know that. [Linked Image]

[This message has been edited by iwire (edited 06-25-2005).]


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#53419 06/25/05 11:42 PM
Joined: Oct 2004
Posts: 265
D
Member
Sorry iwire, I meant that I think its the way the ballast operate, not a difference between the lamps.

Page 1 of 2 1 2

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5