ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Shout Box
Recent Posts
Baseboard Mounted Light Bulb Socket
by SPSchuman. 07/15/19 03:22 PM
Hunter Fan Recalls Brunswick 3 & 4 Light Fans
by Admin. 07/11/19 11:08 AM
Honeywell Recalls some Smoke Sensors
by Admin. 07/11/19 11:03 AM
New in the Gallery:
What is this for?
Plug terminals
Who's Online Now
0 registered members (), 19 guests, and 19 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
motor question... #51829
05/11/05 07:00 AM
05/11/05 07:00 AM
C
cavo148  Offline OP
Member
Joined: Jan 2004
Posts: 79
New Jersey
I have a customer who bought some used 3 phase industrial mixers. One of the three has a single 2hp motor with a voltage rating of 208 delta/ 360 wye, my available voltage is 240 volt, 3ph. The low voltage amps is 6.6 on this motor. Will my available voltage damage this motor which is continuous duty? Need transformer to step down house voltage?
Thanks in advance,
Andy

Work Gear for Electricians and the Trades
Re: motor question... #51830
05/11/05 08:05 AM
05/11/05 08:05 AM
I
iwire  Offline
Moderator
Joined: Jan 2003
Posts: 4,391
North Attleboro, MA USA
First IMO if you do that you have a code violation.

Quote
110.4 Voltages.
Throughout this Code, the voltage considered shall be that at which the circuit operates. The voltage rating of electrical equipment shall not be less than the nominal voltage of a circuit to which it is connected.


Along with that it is a bit high, + or - 10% is about as much as you should push it.

208 + 10% = 229.

240 is little more than 15% high.

I would look into getting a pair of small bucking transformers.


Bob Badger
Construction & Maintenance Electrician
Massachusetts
Re: motor question... #51831
05/11/05 03:22 PM
05/11/05 03:22 PM
F
frenchelectrican  Offline
Member
Joined: Feb 2003
Posts: 939
Wi/ Paris France { France for ...
ok let get this matter straghten out a little here ::

One of the three has a single 2hp motor with a voltage rating of 208 delta/ 360 wye,


is this motor is european designed ??

if so you have suppy of 240 volt 3 phase right now and one of the motor[s] need to buck down to 208 volt to run propely

merci,marc


Pas de problme,il marche n'est-ce pas?"(No problem, it works doesn't it?)

Re: motor question... #51832
05/11/05 04:16 PM
05/11/05 04:16 PM
W
winnie  Offline
Member
Joined: Sep 2003
Posts: 649
boston, ma
What frequency is this motor designed for? If it is a European motor designed for operation at 50 Hz, then use at 60Hz will also enter into the voltage calculation, and if the motor runs faster, then this may impact the operation of the mixer.

All other things being equal, a motor designed for 50 Hz operation will require 6/5 the supply voltage and run at 6/5 the speed on a 60 Hz supply.

-Jon

Re: motor question... #51833
05/11/05 08:32 PM
05/11/05 08:32 PM
H
highvoltageguy  Offline
Member
Joined: Mar 2005
Posts: 53
Silt, Colorado, USA
running a 208 motor on 240 will burn up in time, I know 3 phase motors are exspensive, but is it worth it to buck the voltage down to 208??? well your there to install and make money, but I would think it be better money spent to get a 240v motor beings it only one motor out of the batch he got a deal on.

Re: motor question... #51834
05/11/05 09:11 PM
05/11/05 09:11 PM
C
cavo148  Offline OP
Member
Joined: Jan 2004
Posts: 79
New Jersey
Thanks for the replies. It's certainly not a new motor, so I'm going check the availabilty of a replacement motor rated at the 240 voltage. The nameplate isn't easy to read due to abuse and painting, but I'll check the frequency rating. Besides, it apparently came from the same place as the 240 volt units and was probably fed with 230 or 240 volts there and is ready to die any day.
Andy


Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
Grover
Grover
Sebago, ME, USA
Posts: 109
Joined: January 2005
Show All Member Profiles 
Top Posters(30 Days)
Admin 5
Popular Topics(Views)
256,996 Are you busy
192,874 Re: Forum
182,499 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Release build 20180101)
Page Time: 0.019s Queries: 14 (0.004s) Memory: 0.9765 MB (Peak: 1.1234 MB) Zlib enabled. Server Time: 2019-07-17 06:40:34 UTC