ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat Box
Recent Posts
NEC 2017_392.22(B)(1)(b)
_What's the smallest width

by gfretwell - 09/21/19 11:37 PM
Another weird NEC code question on Feeder Taps
by gfretwell - 09/21/19 11:35 PM
Kichler Lighting Recalls Pendant Lights
by Admin - 09/18/19 08:47 PM
Does a 'normal 3ph-AC motor' include capacitors?
by gfretwell - 09/18/19 01:20 AM
NEC Question_Cord-&-Plug EGC shorter then Neutral
by pcsailor - 09/16/19 05:26 AM
New in the Gallery:
What is this for?
Plug terminals
Who's Online Now
0 registered members (), 12 guests, and 11 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 4 1 2 3 4
Vacuums and Wire Pulls #215621 06/14/15 02:32 PM
Joined: Jan 2005
Posts: 5,316
renosteinke Offline OP
Cat Servant
Member
OK, I'm sure we've all used some method to suck (or blow) a pull-string through a conduit run. I'd like to discuss that: what has worked best for you?

First, do you prefer to use a vacuum to pull the string towards you, or would you rather push it through the line?

If you use a vacuum, which one? Big or small? How have you modified it? What would be the 'ideal' vacuum to have on hand? (Or, should I ask, "two vacuums?")

How do you connect it to the conduit- especially when the pipe is behind a mud ring, off to the side?

Do you make it a practice to tape / caulk / or otherwise seal pipe connections in long runs?

Work Gear for Electricians and the Trades
Re: Vacuums and Wire Pulls [Re: renosteinke] #215622 06/14/15 07:43 PM
Joined: Jul 2004
Posts: 9,394
G
gfretwell Online Content
Member
I like that 3M "toner" vacuum. It is compact with a real good motor. There is enough taper in the hose to fit a lot of holes in the 1-1.5 range and if you have some transition fittings in the box you can get to just about anything.


Greg Fretwell
Re: Vacuums and Wire Pulls [Re: renosteinke] #215623 06/14/15 09:52 PM
Joined: Jan 2005
Posts: 5,316
renosteinke Offline OP
Cat Servant
Member
Would that be the #m #497 HEPA vac? At about $250, price isn't impossible. Shoulder strap and toolbox shape (with internal storage) look like good ideas.

It does not look like you can use it to blow, though.

Re: Vacuums and Wire Pulls [Re: renosteinke] #215624 06/14/15 11:10 PM
Joined: Jul 2004
Posts: 9,394
G
gfretwell Online Content
Member
I have always pulled the mouse. It is hard to get a fitting on the pipe that will still let the string through.
If you are sucking from the far end, you just feed the string and listen for the mouse to go into the filter.


Greg Fretwell
Re: Vacuums and Wire Pulls [Re: renosteinke] #215625 06/15/15 10:55 PM
Joined: Mar 2004
Posts: 947
T
twh Offline
Member
It depends on the compressor, but 100 psi from an industrial system with a big hose can't be beat by a vacuum.

Re: Vacuums and Wire Pulls [Re: renosteinke] #215626 06/15/15 10:57 PM
Joined: Apr 2002
Posts: 7,113
HotLine1 Offline
Member
Greenlee blower/vac system, older version of the current 690. Backup/helper was a Craftsman shop vac.

Push or vac? Sometimes both, most were a mouse and push, occasional 'pull' from the 'backup vac.

Didn't worry about sealing; all was UG PVC.

EMT, and RGC, was 90% fish tape/snake.


John
Re: Vacuums and Wire Pulls [Re: renosteinke] #215627 06/16/15 12:56 AM
Joined: Dec 2000
Posts: 4,281
electure Offline
Member
Jet Line makes a CO2 blowing system.
It has a rubber cone (that goes in the end of the conduit) attached to a hose with a hole in it to feed the string through.
The hose attaches on the other to a high pressure CO2 tank.
It doesn't use electricity and can be used anywhere

It works like a charm. smile

Re: Vacuums and Wire Pulls [Re: renosteinke] #215628 06/16/15 11:28 AM
Joined: Apr 2002
Posts: 7,113
HotLine1 Offline
Member
Sure sounds like it beats having a genset, etc. to drag around.

I wonder if it was 'around' before 2002??


John
Re: Vacuums and Wire Pulls [Re: renosteinke] #215629 06/16/15 11:54 AM
Joined: Dec 2000
Posts: 4,281
electure Offline
Member
If you're talking about the CO2 system, I used a well worn one in the mid '70s. smile

I guess JetLine is now a Gardner Bender product

http://www.gardnerbender.com/en/jo25



Re: Vacuums and Wire Pulls [Re: renosteinke] #215630 06/16/15 11:56 AM
Joined: Jul 2004
Posts: 9,394
G
gfretwell Online Content
Member
CO2 has become pretty expensive stuff. Maybe a tank of compressed air might be a better choice.


Greg Fretwell
Page 1 of 4 1 2 3 4

Featured:

2020 National Electrical Code
2020 National Electrical
Code (NEC)

* * * * * * *

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
togol
togol
NW In. USA
Posts: 421
Joined: September 2005
Show All Member Profiles 
Top Posters(30 Days)
Admin 5
Popular Topics(Views)
258,840 Are you busy
194,361 Re: Forum
183,821 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.3