ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Shout Box
Recent Posts
Linear Power Supply Quits Under Load
by JoeTestingEngr. 10/18/18 08:47 PM
220/230/240V 60Hz Systems
by dsk. 10/17/18 01:25 PM
PLC/HMI Enclosure C2, D1
by ghost307. 10/16/18 03:31 PM
Tingle off the water spigot
by dsk. 10/15/18 02:36 PM
New in the Gallery:
What is this for?
Plug terminals
Who's Online Now
0 registered members (), 41 guests, and 30 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Exterior outlets #207376
10/21/12 11:09 PM
10/21/12 11:09 PM
M
Merlin  Offline OP
Member
Joined: Jan 2004
Posts: 171
NW Indiana
What is your preferred method for installing exterior outlets on a new house? I have done it several way, but wonder what everyone else is doing. I like the Arlington siding boxes, however white does not always match the siding.

The siding contractor will be using 1 1/2" deep siding blocks. I usually let them install them first so they are all even with the siding, then I cut in my boxes.

What do you all use for boxes??

Work Gear for Electricians and the Trades
Re: Exterior outlets [Re: Merlin] #207378
10/22/12 12:33 AM
10/22/12 12:33 AM
E
EV607797  Offline
Member
Joined: Oct 2006
Posts: 745
Fredericksburg, VA, USA
I like to use 3-1/2" deep metal old work boxes with the ears reversed. During rough-in, I leave the cable(s) poked out, let the siding aliens place their block and then I cut in a hole during trim out. Since receptacles are almost always near doors, there is a good chance that the sheathing is wood. We don't see Stryofoam sheathing anymore, but that used to be a concern.

I can't remember which brand of metal boxes have a single screw to adjust the ears, but they allow a bunch of adjustment with regard to depth and angle. The siding blocks allow a good bit of flexibility so that you can cut your hole in the sheathing (a Roto-Zip tool is great for this). Adjust the ears on the box, tip it in through the siding block, sneak a few screws through the ears on the box and you are all set.

Most device covers allow for an insanely-large wall opening, so you should be able to cut a large enough opening in the siding block for the box so that to have access to the ears. You'll also be able have it seated against the sheathing to where there is no gap between the box and device and it remains solid without the siding flexing. A bit of minimally-expanding foam seals the deal.

Obviously, this strategy would never fly with high-volume production jobs, but you know what I mean.


---Ed---

"But the guy at Home Depot said it would work."

Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
Grover
Grover
Sebago, ME, USA
Posts: 109
Joined: January 2005
Show All Member Profiles 
Top Posters(30 Days)
sparky 11
Popular Topics(Views)
250,526 Are you busy
188,088 Re: Forum
177,721 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Release build 20180101)
Page Time: 0.020s Queries: 15 (0.004s) Memory: 0.9437 MB (Peak: 1.0613 MB) Zlib enabled. Server Time: 2018-10-21 09:01:32 UTC