ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Increasing demand factors in residential
by tortuga - 03/28/24 05:57 PM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
Cordless Tools: The Obvious Question
by renosteinke - 03/14/24 08:05 PM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
0 members (), 265 guests, and 15 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
#130645 09/28/06 08:20 PM
Joined: Dec 2001
Posts: 201
A
ayrton Offline OP
Member
I will be hooking up two VFD's on an upcoming project.

There are two existing 3phase pumps, currently started using Nema 1 starters.
We are putting VFD's in place of starters.
Each of the two "buckets" in the MCCenter, have a 3phase 25a braker with a starter.
I beleive the motors are 7 1/2 HP @208V
Will the 25A breakers be enough with the VFD?
I dont know if the Drive has any type of amp draw in itself

Stay up to Code with the Latest NEC:


>> 2023 NEC & Related Reference & Exam Prep
2023 NEC & Related Reference & Study Guides

Pass Your Exam the FIRST TIME with the Latest NEC & Exam Prep

>> 2020 NEC & Related Reference & Study Guides
 

#130646 09/28/06 11:30 PM
Joined: Feb 2002
Posts: 182
B
Bob Offline
Member
Adjustable Speed drives are covered in 430.120. The ampacity of the conductor must be at least 125% of the drive rating.
A 7 1/2 HP has a FLA of 24 amps. I don't think the 25 amps breaker will do.

#130647 10/02/06 07:06 PM
Joined: Jul 2004
Posts: 101
J
Member
Also, if the breakers were part of a UL listed MCC bucket assembly, they might be (probably are) "Mag-only" breakers (aka MCPs), UL "recognized" (UR) only to be used specifically in a listed motor starter assembly. If you don't have the starter, those breakers CANNOT be used as feeders to another device, i.e. your VFDs. They will not have thermal trip elements and are NOT UL listed by themselves.


JRaef
#130648 10/03/06 01:19 PM
Joined: Dec 2001
Posts: 201
A
ayrton Offline OP
Member
I got a hold of the notes on the print, and they say to replace breaker with 60a.
Where does it state in the code I cannot use breaker in MCC bucket w/out thermal protection/starter?

PS I saw your site. (jraef) Nice to have guys like you around.

[This message has been edited by ayrton (edited 10-03-2006).]

[This message has been edited by ayrton (edited 10-03-2006).]

#130649 10/03/06 07:14 PM
Joined: Jan 2005
Posts: 5,445
Likes: 2
Cat Servant
Member
One really must read the directions. As well as follow the instructions.

VFD's often greatly reduce the power required by a motor. They do this by incorporating a "soft start" control, as well as letting you run at a much lower level.

To use one example, a blower that was pulling 28 amps (single phase), was pulling only 8 amps (three phase), while the motors were both of the same horsepower rating. Why? because the blower was only moving the air needed- and not running full speed, fighting a damper.

As for lacking "heaters," well, the few VFD's I've installed all had equivalent circuitry in them. They also had protection for lost phases, etc- comparable to any 'electronic' starter.

I am NOT aware of the UL issue alluded to, and would appreciate some references. As I understand it, breakers (OCPD's) and overload deviced are intended to address very different issues. As the Brits would say, they are as different as cheese and chalk. I suppose "assembly" is the key word there.

#130650 10/07/06 07:35 PM
Joined: Jul 2004
Posts: 101
J
Member
"Where does it state in the code I cannot use breaker in MCC bucket w/out thermal protection/starter?"

240.4 states that you must have over-current protection for all conductors, then goes on to say that motor circuits are covered under article 430.

430.52.C.3 then states that Instantaneous trip circuit breakers can only be used as part of a listed combination motor controller assembly that includes an over-current device (overload relay). If you use the MCP breaker all by itself, it is no longer part of that listed assembly.

Don't get me wrong, this has only to do with MAG-ONLY breakers, commonly referred to as MCPs or Motor Circuit Protectors. Standard Thermal-Magnetic circuit breakers are fine as stand alone feeders.


JRaef
#130651 10/09/06 10:16 AM
Joined: Jan 2005
Posts: 5,445
Likes: 2
Cat Servant
Member
Thanks, jraef. I've just become accustomed to 'inverse time breakers'. What you describe - an assembly- is another thing alltogether.

OOPS


Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5