ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Top Posters(30 Days)
dsk 13
Admin 8
doc 3
Recent Posts
Bathroom electrical
by doc. 08/19/17 06:53 AM
electircal ageing test on IPC
by SIAME. 08/15/17 02:43 AM
electrical aging test on IPC
by gfretwell. 08/15/17 12:27 AM
"Line level" audio on Cat 5?
by gfretwell. 08/08/17 10:39 PM
Fire alarm phone lines and color coding
by gfretwell. 08/08/17 10:26 PM
New in the Gallery:
Gallery Test
Popular Topics(Views)
239,983 Are you busy
175,581 Re: Forum
167,831 Need opinion
Who's Online Now
0 registered members (), 61 guests, and 8 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate This Thread
#109871 - 12/26/05 02:13 AM S/Lights and Pilot wiring  
Trumpy  Offline


Member
Joined: Jul 2002
Posts: 8,217
SI,New Zealand
Photo's and information submitted by RODALCO:
Quote
These first two pics were from a streetlight pole in Kelston which supplies a bus-stop also, it was not working so I had to pull all these wires out of the pole to do some checks. Earth wire was not connected as you can see the cut lug which was supposed to sit under a loose stud in the pole. Final result was wiring ok. just a blown fuse in lighting armature bus-stop. good checking from whoever looks after those bus-shelters.
they blamed a cable fault in the TPS.


[Linked Image]


[Linked Image]

Quote
The next 3 pics are from HW (hot water) pilot fuses on a piece of cardboard in a transformer in Beach Haven. After an HT fault I had to backfeed the LT side, remove the jumpers from the LT bushings to get the power back on.
Probably about 20 years ago, whoever did the job made an attempt to affix the fuses. The card board is just about to fall apart.
Very often pilot fuses are just laying on the bottom of the TX.

The jumpers are visible at the bottom, green 70 mm² earth wire with coloured tape on it.



[Linked Image]


[Linked Image]


[Linked Image]

Thanks a heap Ray!. [Linked Image]


Let's face it, these days if you're not young, you're old - Red Green grin

2017 / 2014 NEC & Related Books and Study Guides

#109872 - 12/26/05 02:21 AM Re: S/Lights and Pilot wiring  
Trumpy  Offline


Member
Joined: Jul 2002
Posts: 8,217
SI,New Zealand
BTW Ray,
Just looking at that third picture.
Is that a split in the insulation on that red phase wire?.


Let's face it, these days if you're not young, you're old - Red Green grin

#109873 - 12/26/05 05:27 AM Re: S/Lights and Pilot wiring  
RODALCO  Offline
Member
Joined: Dec 2005
Posts: 854
Titirangi, Akld, New Zealand
Well spotted, yes there is a cut in the insulation of that red cable.

Thanks for posting my photo's. I will keep my camera handy while doing my jobs all over the place.


The product of rotation, excitation and flux produces electricty.

#109874 - 01/01/06 06:30 AM Re: S/Lights and Pilot wiring  
Arend  Offline
Member
Joined: May 2004
Posts: 19
Joure, Friesland, The Netherla...
Very interesting photo's.

What does HT, LT and TSP exactly mean?

Thanks,

Arend


bzzzzt ;-)

#109875 - 01/01/06 09:36 PM Re: S/Lights and Pilot wiring  
RODALCO  Offline
Member
Joined: Dec 2005
Posts: 854
Titirangi, Akld, New Zealand
[quote]What does HT, LT and TSP exactly mean?[/qoute]

Hi Arend:

HT High Tension, usually 11000 Volts.
LT Low Tension, 230 / 400 Volts.
TPS Tough plasic sheethed. That's the white cable used in wiring up houses, in this case 3 core: Red, Ø. Black, N. Green, Earth. ( not supposed to be used for streetlights unless in conduit.) [Linked Image]

For streetlights nowadays 6 or 10mm² Cu Neutral screened cable is used. Previously 4 mm² single core with single thick or double layers of insulation was used.

I make you a close up photo.


The product of rotation, excitation and flux produces electricty.


Member Spotlight
mersadrad
mersadrad
Montreal, Quebec, Canada
Posts: 28
Joined: March 2011
Show All Member Profiles 
Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Shout Box
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.012s Queries: 14 (0.002s) Memory: 0.7715 MB (Peak: 0.9091 MB) Zlib enabled. Server Time: 2017-08-20 13:48:29 UTC