ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Recent Posts
Chinese motors rated 220 v 50 hertz
by gfretwell - 07/23/24 04:45 PM
100 Definitions: Accessible 2023
by gfretwell - 07/23/24 10:12 AM
100 Definitions, Likely to Become Energized, 2023
by gfretwell - 07/23/24 10:08 AM
240V only in a home and NEC?
by emolatur - 07/18/24 01:05 PM
2023 CEU Course
by gfretwell - 07/17/24 01:08 AM
Advertisement:-Left
Recent Gallery Topics:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
1 members (Scott35), 844 guests, and 33 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Joined: Dec 2000
Posts: 4,294
Member
Quote
Hey, We didn't even need to make a hole through the firewall.

Kent VW


[Linked Image]

Horizontal Ad
Joined: Jun 2004
Posts: 206
C
Member
The sad thing is I see this way to often. Some data guys just have no clue.
Al

Joined: Jan 2003
Posts: 4,391
I
Moderator
Some of you may not recognize what that hole is.

That hole lets HVAC air pass through a fire wall, however the metal duct is a fire damper.

It is held up by pieces of easily melted metal, during a fire it is supposed to drop down and seal off the hole.

It only drops by gravity and the wires passing through will hold it open.

This may seem minor but it is not, smoke is the biggest killer in a fire, this damper was put in for a definite purpose.

IMO running wires through that hole is no different then disabling sprinklers or smoke detectors, it could very well cause death. [Linked Image]

Bob

[This message has been edited by iwire (edited 12-19-2004).]


Bob Badger
Construction & Maintenance Electrician
Massachusetts
A
Anonymous
Unregistered
Iwire hit the nail on the head.

This building is a three story building around 112,000 square feet. All of the ceiling tiles had been removed as the entire building went out for bid for a new tenant. I brought my camera and shot 60 code violations. I could have taken hundreds more. The good news is that part of the bid is to get the building back into compliance.

( I am hoping that my proposal is accepted to completely replace the existing fire alarm system.)

[This message has been edited by kentvw (edited 12-19-2004).]

Joined: Oct 2004
Posts: 806
Member
This is where I bring out my handy wire cutters...SNIP, SNIP, SNIP, SNIP.

Code violation: GONE!
Expression on data guy's face: PRICELESS!

[Edited to add the fourth snip!]

[This message has been edited by mxslick (edited 12-19-2004).]

[This message has been edited by mxslick (edited 12-19-2004).]


Stupid should be painful.
Joined: Jul 2002
Posts: 8,443
Likes: 3
Member
Iwire,
I agree with your comments on this one.
With an open damper in the ceiling, you might as well leave all the doors open in the rooms below as well.
The movement of super-heated air currents in a burning building, is a Fire Brigade's worst enemy, it just helps the fire spread.
GRRR. [Linked Image]

Joined: Nov 2002
Posts: 794
Likes: 3
W
Member
Quote
Some of you may not recognize what that hole is.

That hole lets HVAC air pass through a fire wall, however the metal duct is a fire damper.

The data guy probably thought it was an abandoned air ductwork. Maybe signs describing its purpose and a warning not to pass wires and such thru it posted next to it would help.

Joined: Dec 2000
Posts: 4,294
Member
I'm surprised nobody has noticed the unsealed penetration around the electrician's unstrapped flex.

The data/comm guys aren't the only culprits here.

Joined: Dec 2004
Posts: 8
L
Junior Member
Greetings, I am new to this forum,but have been viewing it for some time. I work in IT BUT I also posess the MN Power Limited Technician low voltage license. Just to let you know I would'nt run any cable in this manner either,and would probably take a pair of cutters to it myself. It's situations like this that prompted Minnesota(where I live) to mandate licensing for low voltage installers. I do a variety of things in IT for my employer,from desktop admin to planning,layout,installation and repair of voice,data, and fiber cables.
I like this website,and enjoy looking at the violation pics. Whenever I feel I'm not doing that great a job installing things,I look at some of these pics and feel rather re-assured..
Sincerely
Low volt ham..

Joined: Dec 2004
Posts: 8
L
Junior Member
Just a follow up-I agree some datacomm people don't have a clue, and many in IT are highly specialized in one small area. Years ago, I worked with a co-worker on a project where I had to construct some special RS-232 adapters that needed resistors between some of the pins,I told her this and her reply was "what's a resistor?" I explained and she said"what's an ohm?" CLUELESS!! She could configure routers etc(so can I). These people should'nt go near any wiring projects.

Page 1 of 2 1 2

Link Copied to Clipboard
Advertisement:-Right

* * * * * * *
Tools for Electricians
Tools for Electricians
 
* * * * * * *

2023 National Electrical Code (NEC)
2023 NEC + Exam Prep Study Guides Now Available!

Member Spotlight
togol
togol
NW In. USA
Posts: 421
Joined: September 2005
Top Posters(30 Days)
Popular Topics(Views)
323,673 Are you busy
247,972 Re: Forum
231,750 Need opinion
New Page 2
Powered by UBB.threads™ PHP Forum Software 7.7.5