ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals

Register Log In

ECN Forum Forums General Topics of the Trade General Discussion Area 1-1/4 EMT bending

ECN Shout Chat

Join in a Live Electrical Chat!

Give a Shout Out!

Electricians revenge
by gfretwell - 05/09/24 08:24 PM

Safety at heights?
by gfretwell - 04/23/24 03:03 PM

Old low volt E10 sockets - supplier or alternative
by gfretwell - 04/21/24 11:20 AM

New in the Gallery:

This is a new one

This is a new one
by timmp, September 24

Few pics I found

Few pics I found
by timmp, August 15

Who's Online Now

1 members (gfretwell), 176 guests, and 12 robots.

Key: Admin, Global Mod, Mod

Print Thread

Rate Thread

Re: 1-1/4 EMT bending

#57682 10/31/05 01:17 AM

Joined: Aug 2005

Posts: 265

S

Offline

Member

I gave up hand-bending 90's on 1 1/4" when the conduit started kinking on me.....now I buy manufactured 90's, but will do offsets when required.

Sixer

"Will it be cheaper if I drill the holes for you?"

Tools for Electricians:

Tools for Electricians, Installers, Maintenance & Service Technicians

Entire Thread
Subject	Posted By	Posted
1-1/4 EMT bending	BigB	10/19/05 01:20 AM
Re: 1-1/4 EMT bending	Cow	10/19/05 02:30 AM
Re: 1-1/4 EMT bending	Gregtaylor	10/19/05 03:12 AM
Re: 1-1/4 EMT bending	renosteinke	10/19/05 03:14 AM
Re: 1-1/4 EMT bending	BigB	10/19/05 03:26 AM
Re: 1-1/4 EMT bending	Peter	10/19/05 03:32 AM
Re: 1-1/4 EMT bending	lamplighter	10/19/05 03:34 AM
Re: 1-1/4 EMT bending	DougW	10/19/05 04:32 AM
Re: 1-1/4 EMT bending	Attic Rat	10/19/05 04:56 AM
Re: 1-1/4 EMT bending	Tesla	10/19/05 04:58 AM
Re: 1-1/4 EMT bending	macmikeman	10/19/05 01:48 PM
Re: 1-1/4 EMT bending	Bill39	10/19/05 02:27 PM
Re: 1-1/4 EMT bending	Steve Miller	10/19/05 07:13 PM
Re: 1-1/4 EMT bending	CanadianSparky	10/19/05 09:50 PM
Re: 1-1/4 EMT bending	e57	10/20/05 06:44 AM
Re: 1-1/4 EMT bending	waymag	10/23/05 02:58 AM
Re: 1-1/4 EMT bending	u2slow	10/23/05 06:04 AM
Re: 1-1/4 EMT bending	earlydean	10/23/05 11:24 AM
Re: 1-1/4 EMT bending	Sandro	10/23/05 11:59 AM
Re: 1-1/4 EMT bending	dillon3c	10/30/05 06:09 PM
Re: 1-1/4 EMT bending	Active 1	10/30/05 06:40 PM
Re: 1-1/4 EMT bending	elektrikguy	10/30/05 06:52 PM
Re: 1-1/4 EMT bending	Alan Belson	10/30/05 08:11 PM
Re: 1-1/4 EMT bending	Sandro	10/30/05 10:53 PM
Re: 1-1/4 EMT bending	Tiger	10/31/05 01:38 AM
Re: 1-1/4 EMT bending	Sixer	10/31/05 05:17 AM
Re: 1-1/4 EMT bending	VAElec	11/01/05 12:14 AM
Re: 1-1/4 EMT bending	Larry Fine	11/01/05 03:29 AM
Re: 1-1/4 EMT bending	elektrikguy	11/03/05 12:09 AM
Re: 1-1/4 EMT bending	e57	11/03/05 12:16 AM
Re: 1-1/4 EMT bending	Amazingmg	11/03/05 10:01 PM

Moderated by dougwells, electure, gfretwell, HotLine1, Scott35, Trumpy

Link Copied to Clipboard

Featured:

Electricians
Slate Coasters

* * * * * * *

Tools for Electricians

* * * * * * *

2023 NEC + Exam Prep Study Guides Now Available!

Member Spotlight

togol
NW In. USA

Posts: 421
Joined: September 2005

Top Posters(30 Days)

Popular Topics(Views)

1,104,166 What do you look like?II

483,527 Tamper resistant: 406.11

411,331 International Wire Colour Codes

320,166 Are you busy

297,943 Norwegian power?

290,215 Permit Snafus...AHJs and Contractors Jump in

245,335 Re: Forum

228,717 Need opinion

228,180 NM Run With An Iron.

227,742 "Esoteric" countries and their wiring practices?

Powered by UBB.threads™ PHP Forum Software 7.7.5