ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Violation?
by renosteinke - 01/27/23 09:52 PM
Does NEC 551.71 (F) apply to dwellings?
by BigB - 01/20/23 10:46 AM
Power submeter connections
by HotLine1 - 01/19/23 09:09 AM
AFDD's coming to the UK
by Texas_Ranger - 01/17/23 07:22 PM
New in the Gallery:
Burger King crown sillyness
Burger King crown sillyness
by wa2ise, December 11
240/208 to a house
240/208 to a house
by wa2ise, October 9
Who's Online Now
0 members (), 20 guests, and 14 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
#106213 04/04/05 05:49 PM
Joined: Oct 2000
Posts: 3,672
Likes: 2
Admin Offline OP
Administrator
Member
Quote
I was a little disappointed to see that NEC 358.24 only says that bends "be made so that the tubing is not damaged." I suppose, though, that the further specification that the radius "shall not be less..." could apply to finding a violation to the sort of free-hand bending as is shown in this photo.

Why spend $8 for a bender, when you can tweak the pipe between studs, bricks, or a handy bumper? :-(

- renosteinke
[Linked Image]

Stay up to Code with the Latest NEC:


2020 NEC & Related Reference & Study Guides
2020 NEC & Related Reference & Study Guides
Pass Your Exam the FIRST TIME with these Exam Prep Combos:
 

>> Master Electrician Exam Prep     >> JourneyMan Electrician Exam Prep
 

#106214 04/04/05 07:22 PM
Joined: Dec 2000
Posts: 4,291
Member
Reno,
I do think the tubing is damaged.
Aah, maybe I'm just picky [Linked Image]

#106215 04/05/05 08:21 AM
Joined: Aug 2003
Posts: 1,374
R
Moderator
Does it make the electrical installation unsafe if the tubing remains undamaged?


Ryan Jackson,
Salt Lake City
#106216 04/05/05 02:36 PM
Joined: Nov 2003
Posts: 269
E
Member
No Ryan, but if I installed the pipe in the pic, I would certainly hope nobody ever found out who did it.


John
#106217 04/06/05 05:59 PM
Joined: May 2004
Posts: 697
D
Member
I think this might fail the "workman-like" test. I confess that I've improved the angle of a conduit over my knee several degrees occasionally when deep in an attic or crawl-space.

Dave

#106218 04/06/05 07:54 PM
Joined: Jan 2005
Posts: 5,370
Likes: 1
Cat Servant
Member
I suspect that one of the bends made is too small in radius to comply with code...and the EMT almost certainly has a "flat spot-" even if this guy stopped just short of a kink.

With workmanship like this, no one should be surprised to see that the EMT is completely unsupported, or to find #12 wires serving a 30 amp water heater (yes, he did that also.) And, of course, no ground wire- even though there is flex used.

#106219 04/06/05 09:59 PM
Joined: Jun 2003
Posts: 1,143
D
Member
Quote
no one should be surprised to see that the EMT is completely unsupported, or to find #12 wires serving a 30 amp water heater

That sounds OK... if he used 2 per leg [Linked Image]

Of course, about the grounding wire... if the flex is under 6', is is required?

[This message has been edited by DougW (edited 04-06-2005).]

#106220 04/08/05 07:37 PM
Joined: Jan 2005
Posts: 5,370
Likes: 1
Cat Servant
Member
Good catch, Doug....that is one of our local requirements: all flex, sealtite get a ground wire.

#106221 04/09/05 09:16 PM
Joined: Apr 2005
Posts: 6
R
Junior Member
WM, 110.12 issue there too. Looks like a 90 with 2 kicks, a twist, and a curl. Unbelievable.

#106222 04/12/05 09:17 PM
Joined: Jun 2001
Posts: 642
N
Member
Joe handy man at work.


ed
Page 1 of 2 1 2

Link Copied to Clipboard
Featured:

Tools for Electricians
Tools for Electricians
 

* * * * * * *
2023 National Electrical Code (NEC)
2023 NEC Now Available!
 
* * * * * * *

2020 Master Electrician Exam Preparation Combos
2020 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
cookcc
cookcc
California ,Long Beach
Posts: 28
Joined: May 2007
Top Posters(30 Days)
BigB 4
triple 3
Popular Topics(Views)
302,740 Are you busy
231,973 Re: Forum
216,688 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.5