The Electrical Contractor Network

ECN Electrical Forum
Discussion Forums for Electricians, Inspectors and Related Professionals

Books, Tools and Test Equipment for Electrical and Construction Trades

Topic Options
Rate This Topic
#116837 - 04/29/04 03:52 AM Nick's Tricks
electure Offline


Member
Registered: 12/24/00
Posts: 4229
Loc: Fullerton, CA USA
Note:
This is the answer to the question posed in http://electrical-contractor.net/ubb/Forum5/HTML/000521.html
AKA: "Wireway the Right Way"

Quote:
Yes, it's the transformer mounting. We had to buy 6X6X1/4" square tube and
weld base plates on it. Then we hoisted the steel up into the wall and
welded the top to the structural steel above and anchored it to the floor.
Unistrut was welded to the steel to make the transformer support. The whole
operation was designed by us and approved by a structural engineer. Welding
was done in house by a certified welder. It turned out pretty clean!

Nick







[This message has been edited by electure (edited 04-29-2004).]
Top
Tools for Electricians:
#116838 - 04/29/04 03:57 AM Re: Nick's Tricks
Lostazhell Offline
Member
Registered: 02/21/04
Posts: 1248
Loc: Bakersfield, CA (Originally Or...
I knew you HAD to have some kinda contraption going on there... Good Idea for whoever came up with it!

Hella lot better than this...



originally from http://electrical-contractor.net/ubb/Forum4/HTML/000346.html

-Randy

[This message has been edited by Lostazhell (edited 04-30-2004).]
Top
#116839 - 04/29/04 11:15 AM Re: Nick's Tricks
Mean Gene Offline
Member
Registered: 10/20/03
Posts: 137
Loc: Ohio, USA
WOW! Good eye Randy. You da man!
Top
#116840 - 04/29/04 01:53 PM Re: Nick's Tricks
BigJohn Offline
Member
Registered: 03/06/04
Posts: 352
Loc: Boston, MA
Wow, was I off!

All the ones I've seen I always sorta assumed (there's that word) that the wall didn't have any additional bracing.

You even have those verticle braces, they were just hidden to make it look all the better. Good job.

-John
Top
#116841 - 04/29/04 03:16 PM Re: Nick's Tricks
electure Offline


Member
Registered: 12/24/00
Posts: 4229
Loc: Fullerton, CA USA
Randy, your picture is of what looks like a demo job in progress.
Where did you take it??
Top
#116842 - 04/29/04 05:00 PM Re: Nick's Tricks
Lostazhell Offline
Member
Registered: 02/21/04
Posts: 1248
Loc: Bakersfield, CA (Originally Or...
Electure.... Its from another post..
I just linked it for comparisons sake.. http://electrical-contractor.net/ubb/Forum4/HTML/000346.html

-Randy
Top

Featured:

2017 NEC and Related
2017 NEC
Now Available!

Shout Box

Recent Posts
License exam
by TRUE POWER
Today at 09:16 PM
Looking for older post
by sparkyinak
Today at 12:27 AM
Members: Non-Members: Did you know?
by Admin
Yesterday at 02:34 PM
Safety at heights?
by HotLine1
01/21/17 08:51 PM
International Wire Colour Codes
by Texas_Ranger
01/21/17 03:29 PM

ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals