The Electrical Contractor Network

ECN Electrical Forum
Discussion Forums for Electricians, Inspectors and Related Professionals

Books, Tools and Test Equipment for Electrical and Construction Trades

Register Now!

Register Now!

We want your input!

Featured:
   

2017 NEC and Related
2017 NEC
Now Available!

   
Recent Posts
Recreational Trailer Power Supply
by David1
10/01/16 04:42 PM
Locked rotor, no burnout
by geoff in UK
10/01/16 02:04 PM
Temporarily feeding a panel...
by Potseal
09/29/16 11:05 PM
Massive power outage South Australia
by Meadow
09/29/16 06:46 AM
short circuit??
by Meadow
09/29/16 06:43 AM
New in the Gallery:
12.5A through 0.75mm˛ flex (just out of curiosity)
Shout Box

Top Posters (30 Days)
HotLine1 11
sparky 10
gfretwell 8
Potseal 7
sparky66wv 6
Who's Online
3 registered (David1, Webmaster, sparkyinak), 89 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Topic Options
Rate This Topic
#197920 - 12/31/10 08:25 AM Makita roto bits??
sparkync Offline
Member

Registered: 10/17/02
Posts: 811
Loc: NC
Does anyone know if Milwallkee? roto bits will interchange with Makita? Or better question, will any of the other brand roto drill bits interchange with Makita. My son gave me a nice makita HR3851 roto hammer, but I need bits for it. I'm having a problem finding the bits I want. Home Depot is a supplier but getting service from them is sort of a pain. That's the only supplier listed around my area. Their site says the drill accepts spline bits. Is this the same as other brands?? Thanks for the input...

Top
Work Gear for Electricians and the Trades

Work Gear for Electricians and the Trades
Work Gear for Electricians and the Trades
Arc Flash Clothing, Gloves, KneePads, Tool Belts, Pouches, Tool Carriers, etc. etc....

#197922 - 12/31/10 11:08 AM Re: Makita roto bits?? [Re: sparkync]
renosteinke Offline
Cat Servant
Member

Registered: 01/22/05
Posts: 5300
Loc: Blue Collar Country
I'll answer this not just for you, but for all those who have never had a 'real' roto-hammer.

Such tools conform to a variety of 'standard' shanks. That is, you are not tied to any particular maker for the bits.

The smallest tools have "SDS" shank bits. Basically a round shank with some flutes and flat spots. These contours allow the bit to be hammered in various directions by the tool, while keeping the tool from hammering itself to pieces.

The next 'size' category has two completely different types of bits, "Spline" and "SDS Max." Like the competing videotape formats, these two types represent different approaches to solving the same problems. While the "spline" type lost the competition, you should be able to easily get a variety of bits from many sources.

The largest category of these tools are 'chisel only" (no drilling), and use different size hex shanks.

Probably the most complete line of bits and core drills is made by Bosch. You'll quickly wonder how you went for so long without the tool.

Top
#197930 - 12/31/10 07:22 PM Re: Makita roto bits?? [Re: renosteinke]
HotLine1 Offline

Member

Registered: 04/03/02
Posts: 6786
Loc: Brick, NJ USA
Sparky:
You should have a WWGrainger store in your area; or you can access them on-line. They carry SDS & spline drive bits and accessories. Another source is Bosch (Online) as they make a full line of bits in all flavors.
_________________________
John

Top
#197937 - 01/01/11 03:08 PM Re: Makita roto bits?? [Re: HotLine1]
sparkync Offline
Member

Registered: 10/17/02
Posts: 811
Loc: NC
Thanks for the replies. I found a "Bolt and Tool Supply" company here where I live. And they had what I wanted. I got me a 1 1/8" masonary bit for now. I'm thinking about getting the 2 1/2" core bit. For one of my previous questions, I think it may help me in cutting out brick for outside lights and outlets. They were considerable less expensive than what I saw online. The saw itself runs about $115.00 and the short extension for about $40.00 or so. Online I was looking at around $ 260/$ 270. I probably should have went ahead and ordered it for tax write off:D But I'm one day too late:(.. Anyway I can use my Makita roto now. I already bought me a "ground rod driver" for it, though I haven't used it yet. I paid around $ 80.00 in all for it. Now I should have fun driving the next ground rods:)

Top



ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals