ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals

Page 1 of 6 1 2 3 4 5 6 >
Topic Options
Rate This Topic
#122256 - 10/23/05 03:19 AM NM Run With An Iron.
iwire Offline
Moderator
Registered: 01/05/03
Posts: 4391
Loc: North Attleboro, MA USA
Here are some pictures from Harold Endean of a very neat NM job.

Harold will have to provide the details.

My apologies to Harold for the delay in posting.

Bob











[This message has been edited by iwire (edited 10-23-2005).]
_________________________
Bob Badger
Construction & Maintenance Electrician
Massachusetts
Top
Tools for Electricians:
#122257 - 10/23/05 05:00 AM Re: NM Run With An Iron.
Trumpy Offline


Member
Registered: 07/05/02
Posts: 8211
Loc: SI,New Zealand
Gees Iwire!,
You been holding out on us with pics like that?.
But I must say, seeing pic's like this mate I can see why.
I'm floored already!.
So neat and tidy, I'm ashamed to look at them.




[This message has been edited by Trumpy (edited 10-30-2005).]
_________________________
Let's face it, these days if you're not young, you're old - Red Green grin
Top
#122258 - 10/23/05 05:04 AM Re: NM Run With An Iron.
Roger Offline
Member
Registered: 05/18/02
Posts: 1716
Loc: N.C.
Absolutely beautiful!

Roger
Top
#122259 - 10/23/05 05:48 AM Re: NM Run With An Iron.
electure Offline


Member
Registered: 12/24/00
Posts: 4259
Loc: Fullerton, CA USA
WOW!!!

I've never seen anything that even comes close to this.


Fantastic. Thanks Harold, & Bob
Top
#122260 - 10/23/05 05:54 AM Re: NM Run With An Iron.
Redsy Offline
Member
Registered: 03/28/01
Posts: 2056
Loc: Bucks County PA
If this is a new home, I'd like to see the quote.
Around here, doing that type of work in developments will get you broke.
Top
#122261 - 10/23/05 06:23 AM Re: NM Run With An Iron.
Kelley Offline
Member
Registered: 07/18/04
Posts: 28
Loc: Masachusetts
harold,

what a nice looking job. Are those lutron homeworks panels to the left in pic #2?
again beautiful work!

Kelley
Top
#122262 - 10/23/05 06:38 AM Re: NM Run With An Iron.
e57 Offline
Member
Registered: 05/27/03
Posts: 2876
Loc: S.F.,CA USA
Neat, very neat!

I wouldn't be able to do that type of work here, well only if I built a wall or partition in front of it. Local code see's romex, and MC below 8' from the finish floor as subject to physical damage. I would have to do that in pipe.

Redsy, Just the appearance of the Homeworks panels, and back-up generator ATS means this was not a low ball job, and there was money/time to take care of the job the right way, and make a spectical of doing so. There was probhably $20K in labor alone earmarked just for that room. Otherwise, customers get skeptical of the rest of the money spent, so it even has to look good to the layman. Without knowing what is on the other end of the runs there, I could take a stab at almost, or just shy of $175-200K electrical contract.

Harold, any pic's of the Tel/data, or AV work in this building? Did you choose the color scheme of the back-boards just to make it all stand out? Nice work chief!
_________________________
Mark Heller
"Well - I oughta....." -Jackie Gleason
Top
#122263 - 10/23/05 07:44 AM Re: NM Run With An Iron.
capt al Offline
Member
Registered: 06/20/04
Posts: 206
Loc: Norton, Ma USA
Harold, very nice job!! There is definitely pride in the work being done in these pictures. It is nice to see craftsmanship is still out there.

Al
Top
#122264 - 10/23/05 07:56 AM Re: NM Run With An Iron.
Ryan_J Offline
Moderator
Registered: 08/19/03
Posts: 1374
Loc: West Jordan, Utah, USA
That is nothing short of amazing! Great job!
_________________________
Ryan Jackson,
Salt Lake City
Top
#122265 - 10/23/05 08:41 AM Re: NM Run With An Iron.
harold endean Offline
Member
Registered: 02/16/02
Posts: 2233
Loc: Boonton, NJ
Sorry I didn't get on sooner, I too have been very busy. Thanks to Bob for posting these pictures. A little history about these pictures. Last year I posted some pictures of a very neat install. ( Maybe Bob can repost them) This house has been being built for about a year or so. It is just now starting to be finished up. I did 4 rough inspections and 2 service inspections to date. the house is about 6-7,000 sq.ft. ( I think) It is huge. 600 amp service and several large panel boards. These pictures you see here are in the main service room. There is all sorts of tel/dat avi work etc. also going on. I will try to get more pictures of that if you like. There is a large gen on the site too. There is about 5-6 HVAC units and an 3 story elevator. I will get some pictures of the outside of the house also if you guys want to see it. The EC has been working very hard here and he is very fussy about his work as you can see.
Kelly, yes, they are large Lutron panels and I believe most of the house lighting will be wired into it. The reason I am unsure about a lot of the info is because the house isn't even compleated yet. {lus the HO changes his mind almost daily. ( This drives the EC crazy) I have no idea what the total cost of the electrical work is because I just see the foreman on the job and not the owner of the elec. comp. This EC does a lot of work in the Morris County area of NJ and the specialize in very large homes. I was inspecting in another town (Medham, NJ)while the regular AHJ was having an operation and the same EC was wiring up another large house. The size of that house made this one look small! The Medham house was about 14,000 sq.ft. I didn't get to see the final product there because the regular AHJ came back to work. The pool house of the one in Mendham was about 2,000 sq.ft. complete with 2 baths and full working kitchen.Any more question, please feel free to ask, and I will try to answer and I promise to get more pictures. This house has a rounded stainglass ceiling that will be back lit when done. I can't wait to see it finished.
Top
Page 1 of 6 1 2 3 4 5 6 >

Member Spotlight
Member Since: 11/17/00
Posts: 2232
New in the Gallery:
SE cable question
Featured:

2017 NEC and Related
2017 NEC
Now Available!

Shout Box


Who's Online
0 registered (), 74 Guests and 10 Spiders online.
Key: Admin, Global Mod, Mod
 
New in the Gallery:
SE cable question
 
Top Posters (30 Days)
Admin 49
HotLine1 43
gfretwell 18
Ruben Rocha 12
Trumpy 9
 
Newest Members
Freecrowder, clee512, Jdscott2005, FAIZAN, Regitest2

ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals