What's in your Tool Belt? Just tring to get an Idea. Thanx :-)

Tool belt? What's that?

In the side pockets of the Skillers, I have a pair of Knipex linemans and small channel locks, insulated phillips and flat head screw driver, and a greenlee level. Oh front pockets: Klien tape measure, fluke volt alert pen, and a calculator. On the belt are the keys to a few tool boxes. Anything more than that will break the camels back.

Whats on the cart? Different story.

Kermit,

If you do a search of the General area here you'll see some previous results from this question.

Bill

I got one of those tool belts, in real hide, a present from No 1 son after he saw Norm toting one in the 'NYW'. Couldn't get on with it, dangling round my nethers and getting in the way.
I don't know about you guys, but stuff like my tape, calipers, plane, rule, pliers etc. has started vanishing off the bench and appearing down the other end of the shop when I SWEAR TO GOD I HAVENT MOVED FROM HERE!

I think it's time for my nap!

Alan

I never got in the habit of actually wearing a Tool Belt. I would usually carry it around slung on my shoulder and put the tools I needed for the job in back pockets and a nail apron (filled with misc. small items needed) in the front.

Bill

Linemans pliers dikes (plier type crimper if I am doing controls)5/16" & 1/4" screw drivers Quick wedge screw driver 422 Channellocks 4way level T5 stripers scratch awl and sometimes 4in1 screwdriver.

Since the great Norm was mentioned, you might notice that he virtualally never uses tools from his toolbelt; he usually picks up a tool from his workbench.
My toolbelt contains an assortment of tools, including ViceGrips 7WR, which allow me to do almost anything. As soon as I get to the work site, I take it off and rest it against my green toolbag. It is merely a means of carrying more weight from my vehicle to the actual working location.
One of my instructors, George Stout, pointed out that for any given task, you only need a very limited number of tools. For instance, pulling wire, I would need my lineman's pliers, wire stripper, number book, black phase tape and gloves. Why would I need to be lugging around nut drivers, RotoSplit, hammer and all the rest of that stuff. People who have three foot diameter tool belts may look impressive but then, that is all the tools they have. I'm beyound that.
Why give up the freedom to wall between studs and past the pretty secretary's desk?
Toolbelts are like pick-up trucks. They are part of the image but not very practical.
~Peter

You drive a pick-up?

You're a hack unless its a 1 ton!

I'm kidding!

1. Fish Tape pulling Linemans
2. Side cutters
3. Crimper
4. Wire Stripper
5. Needle Nose
6. Scratch Awl
7. Small Phillips
6. Med Phillips
8. Large Plillips
9. Tiney Flat Head
10. Small Cabinet Tip
11. Med Cabinet Tip
12. Large Square Shank Flat Head
13. Large worn out Square Shank Flat Head for chipping Plaster and Concrete
14. Adj End Wrench
15. Slip Joint Pliers
16. Large Hex Key set
17. Small Hex Key set
18. Plaster Saw
19. Torpedo Level
20. Flash Light (Mini Mag)
21. Sharpie
22. Pencil
23. Fluke T600
24. Fluke Tick Stick
25. Misc fittings orentied to the work of the day

I think thats it.

>26. Tape Measure
>28. 1/4" Nut Driver
>29. 5/16" Nut Driver
>30. 3/8" Nut Driver
>31. Razor Knife

Now thats it!

Rob

[This message has been edited by sierra electrician (edited 05-24-2005).]

[This message has been edited by sierra electrician (edited 05-24-2005).]

I have a carhart pouch I use...to carry my smokes, phone, tape measure and writing instruments (pen, pencil, sharpie, crayon, whatever). I rarely put a tool in the "tool pouch".

To carry the tools for day/job I use a bucket...a simple empty bucket w/no "liner" with a million pockets on it. It's simple, easy to see in and grab stuff out of...and I can also sit on it if the job calls for it (like putting in devices...bucket full of devices, wirenuts, pigtails, etc).

Two tools are in my pants pocket 90% of the time...my pliers and a 10-in-1 screwdriver (both Klien).

The "tool belt" is for my "stuff", the bucket is for tools.

I was always more like Sierra electrician...40 pounds of stuff around my waste at all times. I don't even change light bulbs without my belt on.

Thanx a lot guys, I start school at Glouster County Votec "NJ" in the fall. They made a new program for in the afternoon insted of morning. There still working on the program, but should be done in time for fall classes. I've been reading a lot in here. You guys / girls are great. I love the advise you all give. I hope to be here for awile. Thanx

Kermit

I have always worn a tool pouch since day 1 in the trade. I cannot stand to watch some of the younger guys running up and down the stairs or ladders for a driver or wirenuts etc. I have a pouch filled with misc parts for the day, phillips driver, small flat head, large flat head, torpedo level, linesmans, needle nose, key hole saw, tape measure, voltage testers, fluke volt pen tester, control screw driver, sharpie, pensil, side cutters and a flashlight. I think I got everything.

I know I will probably be regreting having so much weight on my hips later in life, but it sure saves alot of time going up and down the ladder.

I've developed a "two pouch" style.

My leather "Rough-in" pouch has the following shtuff...

Klein Journeyman "2000 series" steel cutting dikes*
Klein 10-in-1 screwdriver
Elecytrician's hammer
Baby (8") stanley prybar
11" channel - locks
Tubing cutter
Klein (or Ideal) Conduit reaming screwdriver
Klein conduit fitting pliers
Swanson speed-square (6") with box k.o. spaces pre-marked,
Lenox utility knife
30' Tape Measure
China marker
A couple of carpenter's pencils.

This gets put on the double nail pouch belt that holds 8 & 16p nails, assorted conduit straps, 1 1/4" 'drywall' type screws, couplings and connectors.

Obviously, this is used for the "grunt" work... throwing and dropping sticks & hanging boxes.

My "service pouch" is my nice nylon rig with the following:

Klein Journeyman Lineman's pliers w/ tape pulling jaws
K J'man Needle nose pliers
K J'man 2000 dikes
K "wiring tool" (the narrow nose strippers w/crimpers & thread cutters)
K 10-in-1 screwdriver
K #2 & 1/4" slotted screwdrivers
GB Insulated #2 phillips
8" Torpedo Level
Greenlee GFCI/outlet tester
Greenlee volt-tic
Tubing cutter
Channel-locks
Vaco multi-nut driver (the telescoping sleeve one)
Carpenter's pencils
Rolls of tape

Ideal Vol-Con elite ("Wiggy" w/continuity & NCV test)

Clamp-on ammeter (Older... Amprobe/Sperry, perhaps?)

Like anything else, my tool pouches are in a state of continual development. As long as I keep getting different types of jobs, my choice of "at hand" tools will keep fluctuating too...

* The advantages of the "2000" series is that they will cut through steel nails, BX/Greenfield armor & can light hangers w/o developing nicks... so they'll cut regular Cu SOL until the cows come home. JMHO, but they're worth the extra $8-10 over the regular ones.

[This message has been edited by DougW (edited 05-24-2005).]

https://www.electrical-contractor.net/ubb/Forum1/HTML/002065.html

Just bought a new leather tool pouch (Ideal brand) that is flat on the bottom, has a handle and strap and has a lot more room than the hip carring kind. And your tools don't fall out all the time. Works great!

I used a tool pouch for 15 years and started to have back problems. My doctor told me my spine was twisted because of wearing the tool belt every day. What I had done wrong was to have all my tools on one side and things like wire nuts tape and small parts on the other side. This made the tool belt heavier on one side which twisted my spine

I bought a tool bag, made by Rigid, a few months ago. It's great. Large enough for just about everything, including 18 volt drill, hammer, hacksaw, brick chisels and pry bar. The only bad thing is that it weighs a ton but it is worth the trade off to save trips to the van when I need a tool.