ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat Box
Recent Posts
NEC 2017_392.22(B)(1)(b)
_What's the smallest width

by pcsailor - 09/15/19 07:58 PM
NEC Question_Cord-&-Plug EGC shorter then Neutral
by Bill Addiss - 09/15/19 03:19 PM
Does a 'normal 3ph-AC motor' include capacitors?
by gfretwell - 09/15/19 02:17 PM
Another NEC 2017 Question_240/24VAC Txfr-Neutral R
by Bill Addiss - 09/15/19 10:29 AM
Service Question
by HotLine1 - 09/14/19 01:43 PM
New in the Gallery:
What is this for?
Plug terminals
Who's Online Now
0 registered members (), 7 guests, and 12 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
restoring plated bus bar #73255 12/20/06 09:05 PM
Joined: Feb 2005
Posts: 1
R
rgh Offline OP
Junior Member
I just returned from a residential call where a bolted connection on the aluminum bus had over time, become loose and has over heated. The plating has dulled and the bolt holding the connection of two piece bus has that terrible squeek to it when it is either tightened or loosened. It is an out of production panel, and suspect I will not find replacement parts. Is there an acceptable way of cleaning, polishing and retreating the bus to put it back in service ?

Work Gear for Electricians and the Trades
Re: restoring plated bus bar #73256 12/20/06 09:09 PM
Joined: Feb 2004
Posts: 1,431
Lostazhell Offline
Member
you can always have a new piece fabricated... but I have to ask.... Why not just install a new service?

Re: restoring plated bus bar #73257 12/20/06 10:10 PM
Joined: Jan 2003
Posts: 1,429
L
LK Offline
Member
"a bolted connection on the aluminum bus had over time, become loose and has over heated."

I would replace the loadcenter, not worth the the liability risk.

Re: restoring plated bus bar #73258 12/21/06 12:08 AM
Joined: Mar 2004
Posts: 744
B
BigB Offline
Member
Even if you can clean it up and re tighten it, it will fail again. I am pretty sure the aluminum is coated with tin, which is now gone. I have patched them up enough to last a few days till we could change it out. But as the others have said, it needs to be changed out ASAP.

Re: restoring plated bus bar #73259 12/21/06 12:17 AM
Joined: Oct 2006
Posts: 745
E
EV607797 Offline
Member
If you had a custom replacement made, you would be messing with the panel's UL listing by installing non-factory parts. If any metal has been heated to the point that it has been discolored, it can't be trusted anymore, electrically or physically. It must be replaced.

There are lots of companies selling used breakers and panels on the Internet; I would go there via Google to get started. The liability associated with this is way too high to risk replacement with custom-made replacement parts.

By the way, I don't know what brand the panel is that you mentioned, but there is an Eaton (Cutler-Hammer and Westinghouse) facility in Sumter, SC that handles obsolete/out of production products for these brands.

[This message has been edited by EV607797 (edited 12-20-2006).]


---Ed---

"But the guy at Home Depot said it would work."
Re: restoring plated bus bar #73260 12/23/06 07:56 AM
Joined: Jan 2003
Posts: 4,391
I
iwire Offline
Moderator
New Panel time


Bob Badger
Construction & Maintenance Electrician
Massachusetts

Featured:

2020 National Electrical Code
2020 National Electrical
Code (NEC)

* * * * * * *

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
The Watt Doctor
The Watt Doctor
Mont Belvieu, TX
Posts: 437
Joined: December 2001
Show All Member Profiles 
Top Posters(30 Days)
Admin 11
Popular Topics(Views)
258,560 Are you busy
194,143 Re: Forum
183,638 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.3