ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Top Posters(30 Days)
sparky 5
Recent Posts
Dimmable LED 2x4 lay in fixtures
by ghost307. 12/15/17 08:13 AM
2017 NEC Changes
by ghost307. 12/15/17 08:09 AM
Casino Wiring methods
by HotLine1. 12/09/17 10:44 AM
Ground wire Size to water Line.
by HotLine1. 12/05/17 12:11 PM
Flexible conduit to an outside Spa
by gfretwell. 12/05/17 12:28 AM
New in the Gallery:
Gallery Test
Popular Topics(Views)
243,057 Are you busy
179,497 Re: Forum
170,416 Need opinion
Who's Online Now
0 registered members (), 19 guests, and 8 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate This Thread
#63196 - 03/10/06 08:12 PM RNC used for services  
ShockMe77  Offline
Member
Joined: Jun 2005
Posts: 821
Rahway, New Jersey
Maybe this should've gone in the Code portion of the site, but what the heck....

When doing a service in rigid nonmetallic conduit, does the pipe going from the bottom of the meter pan, to the point where the LB enters the structure, need to be fastened within 12" of the bottom of the pan if it is already sturdy w/o a strap? I've always made it a point to make sure a strap was in place if the piece was longer than 12," but today I had a difficult time bending the pipe because of how the siding on the house was.


Work Gear for Electricians and the Trades

#63197 - 03/10/06 08:29 PM Re: RNC used for services  
Electricmanscott  Offline
Member
Joined: Jan 2002
Posts: 1,457
Holden, MA USA
I know I'll be raked over the coals for this but I usually put a screw through the back of the lb and into the house. It is almost impossible to make an offset on such a small piece of pipe.


#63198 - 03/10/06 08:34 PM Re: RNC used for services  
ShockMe77  Offline
Member
Joined: Jun 2005
Posts: 821
Rahway, New Jersey
I know I've done that a few times myself. The most common 'problem' on a residential service (IMO) is the space from where the aluminum siding ends, and the foundation begins. That gap area is what I am referring to.


#63199 - 03/10/06 09:43 PM Re: RNC used for services  
HCE727  Offline
Member
Joined: Nov 2005
Posts: 186
Delaware County, PA, USA
Since we are talking about pvc and services, It would be nice if they made a mogul pulling lb in pvc for those services that you are sleeving seu with. I know the trick about going one size up on the lb, but it looks bad sometimes.


Hank

#63200 - 03/11/06 11:54 AM Re: RNC used for services  
Tom  Offline
Member
Joined: Jan 2001
Posts: 1,044
Shinnston, WV USA
HCE727,

there is a product on the market called "EZ LB" and while it is not a mogul lb, it comes apart so that all that is left when you take the cover off is the 2 hubs & back of the LB. A real knuckle saver IMO.


Few things are harder to put up with than the annoyance of a good example.

#63201 - 03/11/06 08:03 PM Re: RNC used for services  
HCE727  Offline
Member
Joined: Nov 2005
Posts: 186
Delaware County, PA, USA
Tom, is it PVC, who makes it?


Hank


Member Spotlight
cookcc
cookcc
California ,Long Beach
Posts: 28
Joined: May 2007
Show All Member Profiles 
Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Shout Box
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.013s Queries: 14 (0.002s) Memory: 0.7762 MB (Peak: 0.9194 MB) Zlib enabled. Server Time: 2017-12-15 13:48:46 UTC