ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Increasing demand factors in residential
by gfretwell - 03/28/24 12:43 AM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
Cordless Tools: The Obvious Question
by renosteinke - 03/14/24 08:05 PM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
1 members (Scott35), 267 guests, and 20 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
#51981 05/16/05 10:57 PM
Joined: Mar 2004
Posts: 55
E
eswets Offline OP
Member
Installed a new post light last week, and could not get the lights to turn off. Replaced photo cell three times. Voltage was correct and line and load was correct. Finally found the problem. Any guesses to what happened.

#51982 05/17/05 12:04 AM
Joined: Mar 2005
Posts: 212
G
Member
The sun never rose that day? What?!

#51983 05/17/05 06:02 AM
Joined: Oct 2000
Posts: 2,723
Likes: 1
Broom Pusher and
Member
Quote

Installed a new post light last week, and could not get the lights to turn off. Replaced photo cell three times. Voltage was correct and line and load was correct. Finally found the problem. Any guesses to what happened?

Here are some guesses:

<OL TYPE=1>

[*] Did not turn off Power before Connecting Photocell (AKA - Wired it "Hot"),


[*] Did not have the "Light Limiter" slider up far enough (the metallic gizmo which slides over the PC's lens),


[*] Forgot to remove the "Tape" from the Lens after testing it - or (see #4)


[*] Did not remove the protective covering from the lens - if used,


[*] Bad, or non-existent "Neutral" connection to "Common Wire" of Photocell,


[*] Load Current exceeded the max. ratings of the Photocell, forcing it into an Arced closed situation,


[*] Left it in the "Test" mode, or some slider switch setting which relates to motion / light levels, or switch overide,


[*] Photocell was getting hit from something while in operation - like a Tree's Branches blowing in the wind were hitting the Photocell,


[*] Photocell was designed to turn loads "off" when dark, or something in this realm,


[*] Photocell was marked incorrectly - like intended to be used in conjunction with another component, or it was really a motion sensing - "off" or "on" device, or Line/Load incorrectly marked (grasping at straws here)


[*] Lighting Fixture(s) Posessed by a Demon, and Demon has no tolerance for Photo Controlled Apparatii.
</OL>

Any of these come close?

Scott35


Scott " 35 " Thompson
Just Say NO To Green Eggs And Ham!
#51984 05/17/05 08:10 AM
Joined: Dec 2004
Posts: 1,064
D
Member
I had a bitch of a time with photocells a little while back on street lights, had the right voltage, but the buggers wouldn't work when plugged in.

Problem: nuetral tap 3 poles down dropping the nuetral out, when a load was applied.

Dnk.....

#51985 05/17/05 11:38 AM
Joined: Jul 2004
Posts: 9,923
Likes: 32
G
Member
How long are you waiting? The photocells I have will start out "on" and it takes a few minutes before it finally figures out the sun is up. It also seems to take full sun to turn it off.


Greg Fretwell
#51986 05/17/05 11:49 AM
Joined: Sep 2001
Posts: 806
N
Member
Some PC controls have a jumper wire to select operating mode, as well. By cutting or not cutting the wire, you select "Dark=Load OFF" or "Dark=Load ON"

#51987 05/17/05 07:11 PM
Joined: May 2003
Posts: 2,876
E
e57 Offline
Member
The piece of black tape you left over the "eye"?


Mark Heller
"Well - I oughta....." -Jackie Gleason
#51988 05/17/05 08:02 PM
Joined: Feb 2003
Posts: 939
F
Member
other possibtly is the photo cell socket bypassing the photocell circuit

or other possiblty is the photocell is line up wrong way where the eyes is not getting correct light source

or other possiblty is the line - load bypassing the photoeye circuit


Pas de problme,il marche n'est-ce pas?"(No problem, it works doesn't it?)

#51989 05/17/05 08:28 PM
Joined: Mar 2002
Posts: 125
S
Member
Does the post light have a ballast? If so did you conect the photo cell to the socket to photo cell. Had an apperntice do that once. Would not shut off.

#51990 05/17/05 08:33 PM
Joined: Aug 2004
Posts: 186
N
Member
Light is shinning to close to photocell causing it to think its sun. this has happened to me.

Page 1 of 2 1 2

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5