ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
How's Florida doing with Hurricane Ian?
by Bill Addiss - 09/28/22 12:41 PM
Tough being a lineman's kid
by Bill Addiss - 09/28/22 12:39 PM
GFCI's pops in large numbers
by dsk - 09/26/22 04:35 AM
AFCI’s Revisited
by sparky - 09/24/22 09:58 AM
NFPA Price Increase Coming
by Bill Addiss - 09/23/22 02:22 PM
New in the Gallery:
240/208 to a house
240/208 to a house
by wa2ise, October 9
Now you know.
Now you know.
by Tom_Horne, September 7
Who's Online Now
0 members (), 48 guests, and 12 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
#45541 12/01/04 09:43 PM
Joined: Jul 2001
Posts: 62
J
johnd24 Offline OP
Member
On your jobs,who usually installs the ceiling medallions that are used around ceiling light fixtures??? thanks
And do u glue them ??

#45542 12/01/04 10:08 PM
Joined: Jan 2002
Posts: 1,457
E
Member
The few times it has been an issue I have installed them. Don't quite remember how but with this whole gravity thing we have going I must have used some type of adhesive. I do remember it not being a big deal.

#45543 12/01/04 10:52 PM
Joined: Sep 2001
Posts: 806
N
Member
Double-sided foam tape works well

#45544 12/01/04 11:05 PM
Joined: Jan 2004
Posts: 615
J
Member
The carpenter usually did, but when we had to, we would. The carpeneter used polyseam seal. I guess it has give that carpenters like. It'll flex instead of crack over time. Then I just used 2 screws to hold it up while it dried. Then it was left up to the painter to dab and paint to screw (along with the medallion.

#45545 12/01/04 11:05 PM
Joined: Apr 2002
Posts: 914
E
Member
We use adhesive caulk to glue them in, use it to fill in the gap at the ceiling also. For the large ones, we use sheetrock screws to assist until the caulk sets.

#45546 12/02/04 06:46 AM
Joined: Jun 2004
Posts: 613
S
Member
I use a strong adhesive like liquid nails or equal.

I haven't found a way to extend the ceiling box down to be compliant with 314.20

shortcircuit

#45547 12/02/04 09:33 AM
Joined: Aug 2001
Posts: 329
S
Member
We normally put them up. Securing them depends on the size. The small ones (12-15") we do with an adhesive like EE or shortcircuit use. For the big ones (20-36") we glue and put in a few drywall nails near the outside edge. Since they're often styrofoam we use a counter sink to make the indent first then SLOWLY run the screw in to a level of (just barely) below the surface. We get the painter or drywall guy to fill the holes before they paint. Seems to work and nobody has complained about filling the holes for us.


Link Copied to Clipboard
Featured:

Tools for Electricians
Tools for Electricians
 

* * * * * * *

2020 Master Electrician Exam Preparation Combos
2020 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
Radar
Radar
Los Angeles
Posts: 349
Joined: April 2004
Top Posters(30 Days)
dsk 3
Popular Topics(Views)
297,738 Are you busy
228,504 Re: Forum
213,335 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.5