ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat Box
Recent Posts
FPE in Germany
by andey - 10/14/19 10:14 AM
Fuse blower plug?
by gfretwell - 10/13/19 03:23 PM
Power factor and transformer efficiency
by TeslaEdison - 10/13/19 04:05 AM
Help with aging employee advice.
by gfretwell - 10/12/19 01:17 PM
Permit Snafus...AHJs and Contractors Jump in
by HotLine1 - 10/10/19 07:35 AM
New in the Gallery:
FPE Breaker panel in germany
What is this for?
Who's Online Now
1 registered members (Scott35), 5 guests, and 9 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Name The Violation(s)? #186494 05/15/09 02:40 PM
Joined: Oct 2000
Posts: 3,587
Admin Offline OP
Administrator
Member
Quote
A maintenance inspector sent these pics to me when he found the following at a gate motor for a homeowners association. 300.5 violation? Protected from physical harm?

Remember, this is a fairly heavy-vibration area when you factor in traffic and the operation of the motor itself.

Thoughts appreciated.
-Zapped

[Linked Image]

[Linked Image]

[Linked Image]

2017 / 2014 NEC & Related Books and Study Guides
Re: Name The Violation(s)? [Re: Admin] #186500 05/15/09 10:37 PM
Joined: Apr 2002
Posts: 7,121
HotLine1 Offline
Member
Based on the photos....
A 'bell end' or ta with bushings would be nice on the pvc. I'm guessing there is in fact PVC in the nice new cement patch...not just THHN/THWN.

I see three conductors spliced w/red nuts going to the 'hole' that's under the ring...and what looks like a wht/red going???

Nice water visable in the PVC @ 8 o'clock.

That said, physical damage from vibration? that may be a stretch, although a possibility. By 'eye' in the pic, that may be 2" of concrete.....but where's the PVC?

That looks like a 'non-electrician' did it.



John
Re: Name The Violation(s)? [Re: HotLine1] #186504 05/16/09 03:13 AM
Joined: Feb 2003
Posts: 939
F
frenchelectrican Offline
Member
I will agree with John {Hotline1} that nonelectrician done this work and this is not a wise set up.

However I did spotted two conducts there IMO I know one for gate power the second one may be used for intercom { some area will use that } or sepertated feed for something else { just hope no one have a bright idea to throw low voltage system intermixed with line voltage in there.}

Merci,Marc


Pas de problme,il marche n'est-ce pas?"(No problem, it works doesn't it?)

Re: Name The Violation(s)? [Re: frenchelectrican] #186507 05/16/09 01:37 PM
Joined: Oct 2002
Posts: 482
Z
Zapped Offline
Member
Yes, my initial guess would be that the gate-guys pulled this one.

I would guess that the hand-hole in the foreground of the first pic would be the comm wire.

An interesting addition to this mess is that, from what I'm told, the gate motors are tapped into a lighting circuit.

I'm also not too sure that the concrete hand-hole is listed for punching into the side like that, let alone that shallow.

I THINK I see the lip of a 1/2" PVC around that punch-in, but it should, at the very least, come into the hand-hole far enough to protect the wire from the abrasive concrete.

I may be called out to inspect this further, and if so I will post my findings.

Thanks for your responses, and further responses will be appreciated.

Re: Name The Violation(s)? [Re: Zapped] #186564 05/19/09 12:15 PM
Joined: Jul 2004
Posts: 9,408
G
gfretwell Offline
Member
Is this 120v? Most gate operators I see are 12vdc and battery backed up. The question is whether the 120 > 12v conversion is done in this pedestal or in the control box.
The controller will have a lot more wires than a slave unit which only needs "open/close/common".


Greg Fretwell
Re: Name The Violation(s)? [Re: gfretwell] #186696 05/24/09 09:45 PM
Joined: Feb 2002
Posts: 2,233
H
harold endean Offline
Member
Greg,


Here in NJ, most of the gate openers are of the 120 volt style. As Frenchelectrician said, sometimes there are low voltage wires that run with the line voltage for the control wires. They would either have to be of the same caricaturisation or the would have to be run in a separate conduit.

Re: Name The Violation(s)? [Re: harold endean] #186801 05/28/09 10:59 AM
Joined: Oct 2002
Posts: 482
Z
Zapped Offline
Member
Most, actually all, of the motors I've run across at communities are 120V in. They often have battery back-ups, which have enough juice to open the gates in the event of a power failure. All of the voltage adjustments for the control board, battery back-up, etc. are done within the motor/control housing.

I haven't been called out to personally inspect this installation yet. I imagine the community is uninterested in spending money on something "that works". This is usually the case, especially in this economy.


Featured:

2020 National Electrical Code
2020 National Electrical
Code (NEC)

* * * * * * *

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
Posts: 165
Joined: March 2007
Show All Member Profiles 
Top Posters(30 Days)
sparky 10
Popular Topics(Views)
259,506 Are you busy
194,890 Re: Forum
184,329 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.3