ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
Shout Box
Recent Posts
turning down possible problem customer
by HotLine1. 05/21/18 07:53 AM
480 Delta
by sparkyinak. 05/20/18 09:33 PM
Furnace igniter leaking noise to stereo
by sparkyinak. 05/20/18 07:20 PM
electircal ageing test on IPC
by HotLine1. 05/14/18 09:42 AM
What estimating software do you recommend?
by wattsittoyou. 05/14/18 06:28 AM
New in the Gallery:
Plug terminals
Housebilding DIY wiring
Who's Online Now
2 registered members (Tjia1981, ghost307), 9 guests, and 11 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Over Under Sideways Down #111019
08/17/06 08:02 AM
08/17/06 08:02 AM
electure  Offline
OP
Member
Joined: Dec 2000
Posts: 4,266
Fullerton, CA USA
From Rewired (Adam Derus)

Quote
Happen to stumble on these the other day.... Priceless isn't it??



[Linked Image]


[Linked Image]


[Linked Image]

2017 / 2014 NEC & Related Books and Study Guides
Re: Over Under Sideways Down #111020
08/17/06 06:27 PM
08/17/06 06:27 PM
B
BElder  Offline
Member
Joined: Nov 2004
Posts: 51
Paradise, CA. U.S.A.
They had to be done with out permits and no inspection [Linked Image] I sure hope that they were not inspected. and you see what us inspectors have to deal with! Ican here it now Whats Wrong With That [Linked Image]

Re: Over Under Sideways Down #111021
08/17/06 08:21 PM
08/17/06 08:21 PM
J
Jim M  Offline
Member
Joined: Aug 2001
Posts: 457
Chestertown, MD, USA
Seems to be just more examples of people adding corners to a wheel to make it work better.

I guess they couldn't figure out how to make a connection in the wiring compartment.

Re: Over Under Sideways Down #111022
08/17/06 09:04 PM
08/17/06 09:04 PM
Lostazhell  Offline
Member
Joined: Feb 2004
Posts: 1,431
Bakersfield, CA (Originally Or...
Sometimes I seriously wonder if "Doofus" will ever be out of work... Heck, he even though enough to put duct seal over the screw holes! [Linked Image]

Re: Over Under Sideways Down #111023
08/17/06 11:26 PM
08/17/06 11:26 PM
L
Larry Fine  Offline
Member
Joined: Feb 2005
Posts: 693
Richmond, VA
These appear to be roof-top installations. Looks like they didn't want to build pedestald for the disco's.


Larry Fine
Fine Electric Co.
fineelectricco.com
Re: Over Under Sideways Down #111024
08/18/06 12:42 AM
08/18/06 12:42 AM
F
frank  Offline
Member
Joined: May 2001
Posts: 376
windsor ontario canada
How did the high pressure switch get on the service port?That should be inside the unit.I bet it broke and they didn't realize it can be replaced by unscrewing just the switch.That tee fitting most likely has no shrader valve in it and the cap could seriously hurt someone since it's under 400lbs pressure from the liquid refrigerant.Could be a time bomb if a service tech is not paying attention and decides to check the high side pressure.



[This message has been edited by frank (edited 08-18-2006).]

Re: Over Under Sideways Down #111025
08/18/06 06:03 PM
08/18/06 06:03 PM
R
Rewired  Offline
Member
Joined: Jan 2006
Posts: 558
Hamilton, Ontario, Canada
Hey Fellas!

Larry:
Yes these are rooftop units.. I just happen to wander up there when BOTH of the units cooling the floor I am working on stopped working ( Carrier units: JUNK IMHO).
All the other units up there have the discos tagged right to the sides of the units.

Frank:
I am not sure how that switch got there.. I assume from the electrical the same hack did the referigeration as well and probably the original install, as the units on the floor above us have done nothing but leak onto our floor because all the condensate drains have been done improperly according to the NEW service Techs.

A.D


Featured:

2017 Master Electrician Exam Preparation Combos
2017 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
richard
richard
L.I. New York
Posts: 95
Joined: August 2003
Show All Member Profiles 
Top Posters(30 Days)
twh 12
Popular Topics(Views)
246,851 Are you busy
184,206 Re: Forum
173,447 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Release build 20180101)
Page Time: 0.026s Queries: 14 (0.005s) Memory: 0.9856 MB (Peak: 1.1398 MB) Zlib enabled. Server Time: 2018-05-21 13:06:38 UTC