ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat Box
Recent Posts
Unusual Well Pump Switch Failure
by sabrown - 10/28/20 04:31 PM
Look at this mess...
by InspectorE - 10/27/20 09:09 PM
New tool
by gfretwell - 10/24/20 11:09 AM
Where is Everyone?
by Bill Addiss - 10/17/20 07:04 PM
New in the Gallery:
Facebook follies, bad wiring
FPE in Germany pt.2
Who's Online Now
1 registered members (Scott35), 18 guests, and 14 spiders.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
DeWalt Screwdriver #10924 06/22/02 08:15 PM
Joined: Feb 2002
Posts: 840
C
CTwireman Offline OP
Member
I just saw a new DeWalt 7.2 volt screwdriver at Home Depot the other day (where else?) It pivots so that it can either be straight or work like a srewgun. It costs $100 and it's made in China. (where else?)

has anyone purchased this, and if so, what is your impression of it? I'm thinking about buying it, as it seems more handy than a cordless drill for most electrical work since it's much lighter.

Does anyone know of any other brand of cordless screwdriver that is good?


Peter
Work Gear for Electricians and the Trades
Re: DeWalt Screwdriver #10925 06/22/02 08:44 PM
Joined: Jun 2001
Posts: 141
A
amp-man Offline
Member
There are three "pro" level battery screwdrivers.

Milwaulkee 2.4 V and Panasonic 2.4 V (Essentially the same unit)

Panasonic 3.6 V

DeWalt 7.2 V.

I've used all three. The Pana 3.6 is the best in my opinion. The forward-reverse switch is in the best position and it has all the power you need. Second choice, Pana or Mil. 2.4. Same ergonomics, just less power.

The DeWalt is just not as well designed. If I need more power than the 3.6 driver, I use my DeWalT 9.6 drive or for serious stuff (driving 1/4" x 1.5" lag bolts into PT pole, no pilot hole), I use a Makita 12V impact driver. It's amazing and light.

Re: DeWalt Screwdriver #10926 06/22/02 09:52 PM
Joined: Apr 2002
Posts: 257
M
master66 Offline
Member
I've been using the Milwaulkee 2.4 V for years and love it.

Re: DeWalt Screwdriver #10927 06/22/02 11:14 PM
Joined: Nov 2000
Posts: 2,236
sparky66wv Offline
Member
Wow... I use a DeWalt 14.4V drill for my "light duty" screw and drilling work.

I break out the Milwaukee 18V for heavier stuff (7/8" step bit, up to 4" hole saws, up to 3/4" augers, hammer drilling up to 5/8"...) Anything more than that and it's the 120VAC Northern rotary hammer or the 120VAC Makita angle drill depending on the task at hand.

I wish "they" made all drills/drivers with an adjustable clutch. I'd rather use a clutched drill with holesaws than an angle drill, especially a non-variable-speed one...

My partner's Milwaukee angle drill has VSR, but no clutch. Still a great improvement, though.

I'll stop rambling now.


-Virgil
Residential/Commercial Inspector
5 Star Inspections
Member IAEI

Featured:

2020 National Electrical Code
2020 National Electrical
Code (NEC)

* * * * * * *

2020 Master Electrician Exam Preparation Combos
2020 NEC Electrician
Exam Prep Combos:
Master / Journeyman

 

Member Spotlight
Bill Addiss
Bill Addiss
NY, USA
Posts: 3,961
Joined: October 2000
Show All Member Profiles 
Top Posters(30 Days)
Popular Topics(Views)
271,031 Are you busy
205,036 Re: Forum
193,149 Need opinion
Powered by UBB.threads™ PHP Forum Software 7.7.3