The Electrical Contractor Network

ECN Electrical Forum
Discussion Forums for Electricians, Inspectors and Related Professionals

Books, Tools and Test Equipment for Electrical and Construction Trades

Register Now!

Register Now!

We want your input!

Featured:
   

2017 NEC and Related
2017 NEC
Now Available!

   
Recent Posts
Industrail Control Panel bonding per 409.108
by sparkyinak
Yesterday at 06:29 PM
Calling all Non-US members!! (Non-US only)
by aussie240
12/07/16 02:39 AM
Photo Upload Tutorial
by DanK
12/06/16 11:35 PM
Sprinklered equipment 26-008
by bigpapa
12/02/16 04:24 PM
On Delay Relay with Auto Reset
by Potseal
12/01/16 09:59 AM
New in the Gallery:
12.5A through 0.75mm˛ flex (just out of curiosity)
Shout Box

Top Posters (30 Days)
gfretwell 13
HotLine1 10
sparkyinak 8
Texas_Ranger 8
Potseal 6
Who's Online
0 registered (), 236 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Topic Options
Rate This Topic
#78858 - 10/29/01 03:21 PM 1-1/4" EMT Sleeve
frodo Offline
Member

Registered: 05/16/01
Posts: 129
Loc: louisville, ky usa
hi,
does a 1-1/4" EMT stubbed up through the concrete slab into a detached garage have to be bonded?" by the way it was also installed outside the wall"

i was thinking that i would need an emt connector and a bushing on the exterior side and have to set a box on the inside in order to bond the conduit via the EGC in the 10-2 W/G.

i thought it may be easier to just use 1/2" pvc, LB stubbed into the wall and abandon the stubbed up EMT...

i beleive article 250.86 EX 2 releives me of grounding the sleeve.

thanks for any thoughts...

-regards

frodo

[This message has been edited by frodo (edited 10-29-2001).]

[This message has been edited by frodo (edited 10-29-2001).]

Top
2014 / 2011 NEC & Related Books and Study Guides
#78859 - 10/30/01 03:50 AM Re: 1-1/4" EMT Sleeve
sparky Offline
Member

Registered: 10/18/00
Posts: 5545
250.86EX2 (2002) would seem to concere with 334.15B

Q's arise here;

What is a 'short section'?

Why does a 'short section' remain ungrounded , when an elbow does not?
EX 2 vs. EX 3

Top
#78860 - 10/30/01 08:50 AM Re: 1-1/4" EMT Sleeve
bordew Offline
Member

Registered: 08/27/01
Posts: 155
Loc: Vienna,Ohio, USA
if its metal bond it. Thats why PVC is much easier to work with No bonding requirements.
Also any parallel pathes from garage to house need a 4-conductor to the panel.

Top
#78861 - 10/30/01 10:10 AM Re: 1-1/4" EMT Sleeve
ElectricAL Offline
Member

Registered: 10/10/01
Posts: 615
Loc: Minneapolis, MN USA
Frodo,

What are you running through the 1-1/4" EMT?
_________________________
Al Hildenbrand

Top
#78862 - 11/07/01 09:45 PM Re: 1-1/4" EMT Sleeve
frodo Offline
Member

Registered: 05/16/01
Posts: 129
Loc: louisville, ky usa
hi,
thanks for the replies...i got a customer who has a detached garage...whoever poured the foundation told the homeowner to go to lowes and get a 1-1/2 emt 90 to use as a stub up. the 90 is even outside the wall on the inside of the garage!

the homeowner asked me to use it but i declined and just went with pvc.

i was just wondering whether or not IF it were used would it have to be?

i spoke to an inspector that just said.."don't go there"...

i figured he was right..

-regards

frodo

Top
#78863 - 11/08/01 05:15 AM Re: 1-1/4" EMT Sleeve
electure Offline

Member

Registered: 12/24/00
Posts: 4226
Loc: Fullerton, CA USA
I've had to jackhammer out more than a couple of slabs where EMT has been stubbed through them, and has rotted out below the slab. Your idea to not use it is a good one.
***And now, the big bomb*** (250-32 again)
How do you plan on grounding?

Top
#78864 - 11/08/01 01:33 PM Re: 1-1/4" EMT Sleeve
sparky Offline
Member

Registered: 10/18/00
Posts: 5545
ah, 250-32, my favorite code!
but wait!
lemme see, 10-2 w/g per 225.39(b) 30A, 2 circuits max, ok that seems Kosher assuming a 2-cir can....so.....unless this is ONE 30A circuit for a welder, we run a G-rod from the noodle bar
of course the #10 could be for V-drop, and is for a 20A branch no OCPD's ?

frodo,
straighten us out here please!

Top



ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals