The Electrical Contractor Network

ECN Electrical Forum
Discussion Forums for Electricians, Inspectors and Related Professionals

Books, Tools and Test Equipment for Electrical and Construction Trades

Topic Options
Rate This Topic
#47233 - 01/12/05 02:04 PM ITE type E-QP breakers
GEC-1 Offline
Member
Registered: 06/06/01
Posts: 32
Loc: Covington, Georgia USA
I have just run into a panel that uses ITE type E-QP breakers. Where do I find the information that states that Siemens type QP, or type Q breakers are the direct replacements for these?
Top
Work Gear for Electricians and the Trades
#47234 - 01/12/05 02:29 PM Re: ITE type E-QP breakers
Roger Offline
Member
Registered: 05/18/02
Posts: 1779
Loc: N.C.
Seimens bought Gould ITE awhile back (I'm sure you knew that) and can provide you with the information. I would think you could get this off of their web site, however I tried to find something on their site once and found it wasn't very user friendly, but maybe that has changed.


This is the same case as Westinghouse and Cuttler-Hammer.

Roger



[This message has been edited by Roger (edited 01-12-2005).]
Top
#47235 - 01/12/05 02:35 PM Re: ITE type E-QP breakers
GEC-1 Offline
Member
Registered: 06/06/01
Posts: 32
Loc: Covington, Georgia USA
Roger;
I tried thier website, and could find nothing. I called Siemens, and thier people could not give me a straight answer. So I am just looking for someone that might know of a publication that has been put out about the change. My electrical inspector asked me to find it. Thank-you for the help
Top
#47236 - 01/12/05 03:33 PM Re: ITE type E-QP breakers
Roger Offline
Member
Registered: 05/18/02
Posts: 1779
Loc: N.C.
GEC, go to the link below, it shows ITE as being a registered trademark of Seimens.

I don't know if it's enough to make the inspector happy but it may help.
http://www.sea.siemens.com/ssi/include/trademark.html

Roger
Top
#47237 - 01/13/05 04:00 AM Re: ITE type E-QP breakers
GEC-1 Offline
Member
Registered: 06/06/01
Posts: 32
Loc: Covington, Georgia USA
Roger;
Thanks for the link. I printed it for the inspector and will follow up later this afternoon. Thank goodness I know all the inspectors in this county, so maybe this will be enough for him. Again thankyou for your help.

Paul
Top

Featured:

2017 NEC and Related
2017 NEC
Now Available!

Shout Box

Recent Posts
Looking for older post
by sparkyinak
Today at 12:27 AM
License exam
by TRUE POWER
Yesterday at 11:33 PM
Members: Non-Members: Did you know?
by Admin
Yesterday at 02:34 PM
Safety at heights?
by HotLine1
01/21/17 08:51 PM
International Wire Colour Codes
by Texas_Ranger
01/21/17 03:29 PM

Who's Online
1 registered (Admin), 117 Guests and 10 Spiders online.
Key: Admin, Global Mod, Mod
New in the Gallery:
Desk-mounted "power-board"
Top Posters
gfretwell 9066
Trumpy 8560
pauluk 7693
HotLine1 6833
sparky 5545
Member Spotlight
Tom
Tom
Member Since: 01/01/01
Posts: 1069

ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals