The Electrical Contractor Network

ECN Electrical Forum
Discussion Forums for Electricians, Inspectors and Related Professionals

Books, Tools and Test Equipment for Electrical and Construction Trades

Register Now!

Register Now!

We want your input!


2017 NEC and Related
2017 NEC
Now Available!

Recent Posts
Parking lot pole light swap....
by gfretwell
Yesterday at 08:46 PM
International Wire Colour Codes
by Tjia1981
10/23/16 12:08 PM
Son of Sparky
by HotLine1
10/20/16 07:43 PM
Speaking of Plugmold ...
by gfretwell
10/17/16 02:37 PM
Broken battery charger? Check for cobwebs!
by gfretwell
10/17/16 02:30 PM
New in the Gallery:
12.5A through 0.75mm˛ flex (just out of curiosity)
Shout Box

Top Posters (30 Days)
gfretwell 14
HotLine1 7
ghost307 7
renosteinke 6
Potseal 4
Who's Online
1 registered (gfretwell), 321 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Topic Options
Rate This Topic
#183913 - 01/26/09 05:00 PM code compliant water plugging method
falcondfb Offline

Registered: 09/28/02
Posts: 37
Loc: Jersey, USA
does anyone know of an approved method of plugging the end of a pipe in a cabinet.

I have 3 pvc 4" pipes coming into a main service disconnect feeding a building. One of the pipes has a very small leak but over the last 10 years has caused corrosion on the breaker and buss bars and the unit has to be replaced. We are trying to avoid ripping up 120' of parking lot to replace one of the pipes and the additional down time to the building. I know I cant just stuff hydro lock concrete into the end but I was wondering if there is a UL listed and approved product or if we have no choice but to rip it up.

I am not on the hook for the original job in any way and I could use the extra work but the decision is up to an association of doctors and you know how they can be.

I would like to present 2 options instead of loosing the job altogether.

Work Gear for Electricians and the Trades

Work Gear for Electricians and the Trades
Work Gear for Electricians and the Trades
Arc Flash Clothing, Gloves, KneePads, Tool Belts, Pouches, Tool Carriers, etc. etc....

#183915 - 01/26/09 05:05 PM Re: code compliant water plugging method [Re: falcondfb]
HotLine1 Offline


Registered: 04/03/02
Posts: 6792
Loc: Brick, NJ USA
Hold on to your wallet...OZ Gedney has a bushing type device that is intended to seal UG conduits.

They are specific to pipe size AND conductor size, and more than likely not a stock item.

Check the OZ Gedney website.

#183917 - 01/26/09 05:33 PM Re: code compliant water plugging method [Re: HotLine1]
Trumpy Offline


Registered: 07/05/02
Posts: 8532
Loc: SI,New Zealand
This might be a very long shot, but how about the idea of using adhesive-lined heat-shrink, the heavy Raychem stuff?

Just a ball-park idea.
Let's face it, these days if you're not young, you're old - Red Green grin

#183919 - 01/26/09 05:50 PM Re: code compliant water plugging method [Re: Trumpy]
renosteinke Offline
Cat Servant

Registered: 01/22/05
Posts: 5305
Loc: Blue Collar Country
"Code compliant" is pretty much a phantom here ... along the lines of "good workmanship."

Ductseal might work ... and is commonly used to seal pipe where condensatiohn may occur.

The packing and "chico" used in hazardous location stuff would also work .... IF you could get it in!

Otherwise, testing of various cables has shown that there is generally not an issue regarding spray foam damaging wire insulation. Maybe a squirt is in order.

BUT ... brilliant ideas aside .... what will happen when - not if, but when - the dam breaks? Do you want water to enter a quart at a time?

I'd say any patch is just that - a temporary measure until a more permanent fix can be made.

#183921 - 01/26/09 06:08 PM Re: code compliant water plugging method [Re: renosteinke]
falcondfb Offline

Registered: 09/28/02
Posts: 37
Loc: Jersey, USA
the spray foam thing was tried by someone in the past without success. The adjuster for the insurance co is thinking along the same lines of... a patch is temporary.
I tend to agree. We pride ourselves on doing it the right way. I think the best solution so far is the OZ Gedney conduit sealing bushings. I will call the company in the a.m. and see if application fits.

Please continue with suggestions if we have over looked an option and thanks for the replies so far.


ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals