ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals

Page 1 of 3 1 2 3 >
Topic Options
Rate This Topic
#175715 - 03/09/08 12:07 PM harbor freight tools
sbi Offline
Member
Registered: 03/01/08
Posts: 47
Loc: indiana
what do u guys think of harborreight tools. there is one in my town that i went to the first time yesterday and i was not so impressed.
_________________________
when in doubt jump it out
I happily work for slumlords
Top
Work Gear for Electricians and the Trades
#175716 - 03/09/08 12:34 PM Re: harbor freight tools [Re: sbi]
Active 1 Offline
Member
Registered: 02/22/03
Posts: 687
Loc: Grayslake IL, USA
They are ok for tools or equipment not used much. Such as at home on the weekends or one use items. I got a nice auto darkening welding helmit for less than $50 and a paint spray gun for $40, a neadle scailer. The items I'm happy with.

What I don't like is it's all from China. But you go to Sears, Home Depot, Menards, etc. and most of the off brand odd ball tools are still From China. The above store just charge more.

Top
#175718 - 03/09/08 01:03 PM Re: harbor freight tools [Re: Active 1]
HotLine1 Offline


Member
Registered: 04/03/02
Posts: 6775
Loc: Brick, NJ USA
IMHO, tools for either a DIY, or as above....one use items. I saw a nail gun awhile back...$40; only used nails they sold....but they were 'pre-rusted' & from China.

Remember the old saying...ya get what ya pay for (sometmes)

_________________________
John
Top
#175720 - 03/09/08 01:50 PM Re: harbor freight tools [Re: HotLine1]
sbi Offline
Member
Registered: 03/01/08
Posts: 47
Loc: indiana
i got a 24oz framing hammer and it allready broke. Only had the thing 1 day. went to pull a staple out of a wall and the whole handle pulled apart.
_________________________
when in doubt jump it out
I happily work for slumlords
Top
#175723 - 03/09/08 02:04 PM Re: harbor freight tools [Re: sbi]
renosteinke Offline
Cat Servant
Member
Registered: 01/22/05
Posts: 5316
Loc: Blue Collar Country
I have used several Harbor Freight tools, with great success, for years. I've also seen pure junk sold by them.

IMO, the cheap tool on the truck almost always trumps the fancy tool you can't afford to buy. Many times, it is the blades / bits / accessories that make a tool perform, more so than the tool itself. For example, I have probably spent three times as much on bits, than I did on my roto-hammer itself.

There are some tools too important for you to compromise on, or take chances with. I might take a chance with an umbrella - but that parachute needs perform 100% every time!

I dislike the temptation to judge items by brand name alone. Almost every "quality" manufacturer out there has a few products that are disappointments.
Top
#175724 - 03/09/08 02:25 PM Re: harbor freight tools [Re: renosteinke]
wire_twister Offline
Member
Registered: 07/25/07
Posts: 265
Loc: Georgia USA
I have a few items from Harbor Freight, and for the most part I am happy with them. Bought a 10" sliding compound miter saw for 99 dollars about 7 years ago, it still works, not as fast or as prety as a DeWalt but the dewalt is about 500, and I am not a carpenter so there is no way I would use one enough to pay for the dewalt. When I worked in a textile mill I bought 2 sets of the Pittsburg Forge combination wrenches, used them for years never had one to break. I think they are too big and thick to work on any newer cars with, but they worked for me in that job. I bought a 125lb Russian made anvil for less than 1 dollar a pound, the chinese version was 1.10 per pound. Just as has been already said some tools are worth it and some are not.
_________________________
Jimmy

Life is tough, Life is tougher when you are stupid
Top
#175725 - 03/09/08 02:58 PM Re: harbor freight tools [Re: wire_twister]
BryanInBalt Offline
Member
Registered: 05/11/07
Posts: 47
Loc: Baltimore
I'll buy name brand stuff from them and I'll buy simple tools (no or maybe one moving part) for light use work.

But I've seen too much of their other crap fail to ever buy a power tool or much of anything I'd bring to a paying job.

YMMV
_________________________
Design-Build isn't supposed to mean design *as* you build.
Top
#175726 - 03/09/08 04:29 PM Re: harbor freight tools [Re: BryanInBalt]
macmikeman Offline
Member
Registered: 07/16/02
Posts: 717
Loc: Honolulu, Hawaii
There is a Northern Tool Supply store right around the corner from the condo my mom owns in Fort Myers. I was visiting in October and November so I walked in one boring day. I got all kinds of cheap China stuff to take home, and so far am pleased with it all. Best value for dirt cheap was the carbide unibit set for under $20 bucks and the several multimeters for $1.95 in the discount rack. Christmas gifts. I have no problem dragging a $1.95 multimeter into an attic. If I forget it up there so what. Please no safety speeches, it will never see any voltage above 240. Got a good working amp clamp on meter with a large jaw for under $20 bucks. My Fluke cost more than 10 times that amount, and it didn't make 10 years so we will see which one was the better value in 9-1/2 years from now.
Top
#175738 - 03/09/08 10:46 PM Re: harbor freight tools [Re: macmikeman]
noderaser Offline
Member
Registered: 03/01/07
Posts: 404
Loc: Portland, Oregon, United State...
Although I would stay away from their power tools (unless it's something you would absolutely use only once in a blue moon), their hand tools are starting to carry lifetime warranties. Since I work a lot in situations where tools can walk off, I like the low prices.

It's like my cheapo pocket knives; if I loose an $80 Benchmade, I feel really stupid. If I break or loose my $1 made in China knife, I pull another one out of the drawer and keep working.
_________________________
http://www.hsiprodsvcs.com/
Top
#175741 - 03/10/08 05:15 AM Re: harbor freight tools [Re: noderaser]
NJwirenut Offline
Member
Registered: 09/15/01
Posts: 806
Loc: Bergen County, NJ
A couple years ago I got a job that required a few custom bends in 1-1/2" RMC. Because most of my work is either residential or control/instrumentation stuff, I didn't have a bender that would handle the job. I was going to rent one for the job, but Northern Tool had a hydraulic pipe bender for sale for less than a 2-day rental on a Greenlee would have cost me.

Sure, this thing isn't even remotely close to a Greenlee in build quality, but for a tool that might only get used for one small job, it's hard to justify shelling out $$$ for the "Made in USA" version. If I was bending rigid on a regular basis, it would be a different story.

Cheap tools have their place, particularly for "one-off" jobs, or if you want a tool that you can modify to do some strange function.
Top
Page 1 of 3 1 2 3 >

Member Spotlight
Member Since: 07/05/02
Posts: 8211
New in the Gallery:
SE cable question
Featured:

2017 NEC and Related
2017 NEC
Now Available!

Shout Box


Who's Online
0 registered (), 42 Guests and 8 Spiders online.
Key: Admin, Global Mod, Mod
 
New in the Gallery:
SE cable question
 
Top Posters (30 Days)
Admin 51
HotLine1 43
gfretwell 17
Trumpy 16
Ruben Rocha 13
 
Newest Members
clee512, Jdscott2005, FAIZAN, Regitest2, sureshazhagai

ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals