ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals

Topic Options
Rate This Topic
#148673 - 02/24/02 04:25 AM 1 Phase Trans. Schematics-Part 2
Scott35 Offline

Broom Pusher and
Member
Registered: 10/19/00
Posts: 2707
Loc: Anaheim, CA. USA
These Schematics have been brought over from the "Theory Area" for your convenience.



1 Phase 2 Wire - Series Connected w/ polarity marks.

Related Text From Original Post


Topic: 1 Phase 2 wire-series connected
Scott35
Moderator
posted 06-23-2001 12:14 PM



Schematic[s] of a 1 phase transformer with split coils on primary and secondary. Both sides are connected in
series additive format [higher listed voltage].



Scott SET... posted 06/23/01



1 Phase 2 Wire - Parallel Connected w/ polarity marks.

Related Text From Original Post


Topic: 1 phase 2 wire-parallel connected
Scott35
Moderator
posted 06-23-2001 12:18 PM



Schematic[s] of single phase transformer with split coils on primary and secondary sides - connection in
parallel [sync polarity observed], which would be for the lower listed voltage.



Scott SET... posted 06/23/01



1 Phase 2 Wire - Series Primary-Parallel Secondary, w/ polarity marks.

Related Text From Original Post


Topic: 1 phase schematic-"half and half"
Scott35
Moderator
posted 06-23-2001 12:22 PM



Schematic of single phase 2 wire transformer with split coil primary and secondary - primary in series additive
[higher listed voltage], secondary in parallel w/ sync polarity [lower listed voltage].



Scott SET... posted 06/23/01



1 Phase 3 Wire - Center Tapped Secondary, w/ polarity marks.

Related Text From Original Post


Topic: 1 phase schematic-single coils/tapped sec.
Scott35
Moderator
posted 06-23-2001 12:27 PM



Schematic of single phase 3 wire transformer with single winding primary and secondary.
Secondary has physical 50% tap [center tap], for multiwire use.
Note only one polarity marker per winding.



Scott SET... posted 06/23/01



1 Phase Transformer - Multi 2 wire Secondary, w/ polarity marks.

Related Text From Original Post


Topic: 1 phase schematic-multi 2 wire secondaries.
Scott35
Moderator
posted 06-23-2001 12:38 PM



Schematic of a single phase transformer with single coil primary and three separate two-wire secondaries.
The secondaries are isolated from each other [individually wound to the core] and have no center taps.
Note polarity marks on all coils are on one end only [typically on a certain #1 end].



Scott SET...posted 06/23/01

------end------
_________________________
Scott " 35 " Thompson
Just Say NO To Green Eggs And Ham!
Top
Test Equipment:
Large Selection of Test Equipment For Electrical, HVAC, Test & Measurement
Large Selection of Test Equipment For Electrical, HVAC, Test & Measurement

Member Spotlight
Member Since: 02/23/13
Posts: 204
New in the Gallery:
SE cable question
Featured:

2017 NEC and Related
2017 NEC
Now Available!

Shout Box


Who's Online
0 registered (), 109 Guests and 8 Spiders online.
Key: Admin, Global Mod, Mod
 
New in the Gallery:
SE cable question
 
Top Posters (30 Days)
Admin 47
HotLine1 43
gfretwell 19
Ruben Rocha 12
Trumpy 9
 
Newest Members
Scotto, Freecrowder, clee512, Jdscott2005, FAIZAN

ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals