The Electrical Contractor Network

ECN Electrical Forum
Discussion Forums for Electricians, Inspectors and Related Professionals

Books, Tools and Test Equipment for Electrical and Construction Trades

Register Now!

Register Now!

We want your input!

Featured:
   

2017 NEC and Related
2017 NEC
Now Available!

   
Recent Posts
Calling all Non-US members!! (Non-US only)
by aussie240
Yesterday at 02:39 AM
Photo Upload Tutorial
by DanK
12/06/16 11:35 PM
Sprinklered equipment 26-008
by bigpapa
12/02/16 04:24 PM
On Delay Relay with Auto Reset
by Potseal
12/01/16 09:59 AM
Wow, that was close!
by jraef
11/28/16 07:06 PM
New in the Gallery:
12.5A through 0.75mm˛ flex (just out of curiosity)
Shout Box

Top Posters (30 Days)
gfretwell 13
HotLine1 9
Texas_Ranger 8
sparkyinak 7
Trumpy 6
Who's Online
0 registered (), 196 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Topic Options
Rate This Topic
#126763 - 12/03/06 12:50 PM need a little help
tim89 Offline
Junior Member

Registered: 12/02/06
Posts: 2
Loc: Sewickley, PA, USA
hi, i'm new here and was wondering if someone could give me some advice on a small job i'm working on. i'm wiring two rooms and a bathroom in a basement for a relative and having a problem keeping the outlets on all the time. i was trying to do a loop circuit from the feed at the light to the switch and then feed the outlets from the switch box outlets always on. i was wondering if i should run a three wire from the light to the switch

Top
#126764 - 12/03/06 12:57 PM Re: need a little help
Lostazhell Offline
Member

Registered: 02/21/04
Posts: 1248
Loc: Bakersfield, CA (Originally Or...
Hello Tim,
If you are having probs keeping the outlets on when there is no load connected to them, you likely have a dead short someplace... Beyond that, I'm not sure what you're describing as a "Loop Circuit" would be something that would meet NEC standards..

You should contact a qualified electrician in your area who can see what's been done, and what needs to be done first hand.

Top
#126765 - 12/03/06 01:08 PM Re: need a little help
tim89 Offline
Junior Member

Registered: 12/02/06
Posts: 2
Loc: Sewickley, PA, USA
i'm feeding the swicth from the light then a run to the two outlets but the switch will work the light just fine but the outlets are on when the switch is off but go out when switch is on. i took two year course in high school at a vo-tech, then i did a couple of courses about a year and a half ago.

Top
#126766 - 12/03/06 01:33 PM Re: need a little help
bot540 Offline
Member

Registered: 09/14/04
Posts: 177
Loc: Vernon Hills, IL
Do yourself a favor and call an electrician
_________________________
Jesus may have been a capenter,but God was an electrician.Genesis1:3

Top
#126767 - 12/03/06 01:34 PM Re: need a little help
Roger Offline
Member

Registered: 05/18/02
Posts: 1779
Loc: N.C.
Tim, I hate to do this but I am going to close this thread. I agree with Lostazhell, you need to get a local electrician to help you even if it is for a fee.

Trying to give advise in a forum and have it understood is not easy even when we as tradespeople are the participants in the discussion.

I know you wouldn't want to have anything happen to your relatives or their possessions.

Roger

Top



ECN Electrical Forums - sponsored by Electrical Contractor Network - Electrical and Code Related Discussion for Electrical Contractors, Electricians, Inspectors, Instructors, Engineers and other related Professionals