ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Increasing demand factors in residential
by gfretwell - 03/28/24 12:43 AM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
Cordless Tools: The Obvious Question
by renosteinke - 03/14/24 08:05 PM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
2 members (Scott35, gfretwell), 275 guests, and 12 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Joined: Oct 2002
Posts: 830
S
Member
I'm doing a low voltage project, and not use to the amperage etc. the smaller wires. When calculating the amperage, I'm assuming the math technique is the same. I have 1 alarm that is 15 watts. the voltage is 12 volts. Therefore 15 watts divided by 12 volts gives me 1.25 amps. This is the right formula no matter what the voltage etc. is, isn't it? I need a little assurance here:; Thanks ..

Joined: Jul 2002
Posts: 680
W
Member
Ohms law applies at low voltage.

Joined: Oct 2002
Posts: 830
S
Member
Thought so; Thanks ....

Joined: Jul 2004
Posts: 625
S
Member
That's not Ohm's Law, however...

Joined: Oct 2003
Posts: 156
D
Member
Ohm's law applies, but when working with LV, wire and connection resistance comes into play. I assume your device consumes 15 watts over a range of voltage say from 11 to 14 volts applied at the device.

Joined: Aug 2001
Posts: 335
S
Member
Just as an FYI: if your project is security alarm or fire alarm there are other requirements for the load calc.

Also be a bit careful about the length & size of the wires. #18/20/22 alarm wiring is often very long runs and can add a lot more resistance than the 14/12/10 we normally use.

Joined: Nov 2002
Posts: 794
Likes: 3
W
Member
A certian length of say 14 gauge wire will have the same voltage drop at the same amps no matter what the supply voltage is. However, that voltage drop will be a bigger percentage of the supply voltage when the supply voltage is lower. Thus, what is an acceptable drop at 120V would be bad when the supply is 12V. 12 volt light bulbs will look dimmer than 120V bulbs seeing the same voltage drop. This is a big reason why POCOs use high voltages for long distance transmission.

Joined: Jul 2002
Posts: 680
W
Member
Quote
That's not Ohm's Law, however...
Isn't it derived from ohms law though??. Seem to remember someone proving that one time or another?

Joined: Jul 2004
Posts: 625
S
Member
Ohm's Law is E = IR.

Watt's Law is P = IV.

Joined: Oct 2002
Posts: 830
S
Member
My "Ugly's book" says that the three basic Ohm's law formulas are: I=E/R, R=E/I, and
E= IxR

I = Amperes
E = Volts
R = Ohms
P = Watts

Maybe Ugly's wrong [Linked Image] Thanks anyway for the input... Steve

Page 1 of 2 1 2

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5