ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
UL 508A SPACING
by ale348 - 03/29/24 01:09 AM
Increasing demand factors in residential
by tortuga - 03/28/24 05:57 PM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
1 members (ale348), 302 guests, and 14 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
#205432 02/21/12 12:12 AM
Joined: Apr 2002
Posts: 7,381
Likes: 7
Member
Scenario: Sheetmetal ductwork for a dust collector system in a woodshop.

(5 HP, 3 phase, 208 volt motor)

Does the ductwork require any bonding? How about static?

Any code references appreciated.


John
Joined: Jul 2004
Posts: 9,923
Likes: 32
G
Member
I would assume the duct work gets bonded via the EGC to the dust collector motor and enclosure. This is similar to a duct heater.
Static is a whole 'nother thing, particularly if this is a plastic duct. In some of the woodworking BBs they have discussions about this. The fear is "lightning" in the duct could cause an explosion. I would think simply bonding a metal duct would bleed off the static charge.

I do not know of any article that deals with this unless you can call it "pipe" 250.104(B)


Greg Fretwell
Joined: Apr 2002
Posts: 7,381
Likes: 7
Member
Greg:
I'm looking for any requirement, other than 'spec' for this.

The two woodshops I installed dust collector systems in years back both had duct bonding on the 'specs'.



John
Joined: Jan 2005
Posts: 5,445
Likes: 2
Cat Servant
Member
I believe the bonding requirements are in the Mechanical code, and are dependent on the CFM of the unit. That is, your typical home workshop collector isn't big enough to require it.

Ironically, the problem is with plastic ducts, rather than metal ones.

Joined: Apr 2002
Posts: 7,381
Likes: 7
Member
Reno:
Thanks for the input. I searched the mech code to no avail, it sends ya to NFPA codes, and that is vague also.

I dumped this back to the design pro to see what kind of response I get from him/them.



John
Joined: Jul 2004
Posts: 9,923
Likes: 32
G
Member
Maybe this gets back doored in by the manufacturer's installation instructions.

Other than that I can't find anything either.

It is probably like steel studs and the NFPA is waiting for a body or two.


Greg Fretwell
Joined: Feb 2002
Posts: 2,233
H
Member
John,

I had computer issues the past month so I wasn't on line.

I have seen the plastic dust collectors have a bonding wire run along side of them to discharge the static when sucking up the dust, but I haven't seen too many metal duct collector systems. My guess is that the metal will bleed off any static as it starts to build up as long as the metal duct is attached to a grounded piece of equipment.

Joined: Apr 2002
Posts: 7,381
Likes: 7
Member
Harold:
Thanks for that. At the moment, the job seems to be in limbo for some reason.



John
Joined: Nov 2007
Posts: 764
K
Member
From what I can find on the subject, the general consensus seems to be that with that type of installation the bare wire should be run inside the plastic duct to actually be effective. Placing it outside supposedly does nothing to dissipate any static build up inside the duct, which apparently is where the dust ignition problems occur.

Joined: Jul 2004
Posts: 9,923
Likes: 32
G
Member
They do make this stuff (conductive duct) but it ain't cheap.

http://www.globalindustrial.com/p/h...-duct-black-12-inch-dia-15-ft-long-strap


Greg Fretwell

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5