ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Increasing demand factors in residential
by gfretwell - 03/28/24 12:43 AM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
Cordless Tools: The Obvious Question
by renosteinke - 03/14/24 08:05 PM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
1 members (Scott35), 267 guests, and 17 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
#152306 07/02/04 11:58 AM
Joined: Jan 2003
Posts: 4,391
I
iwire Offline OP
Moderator
Has anyone worked wih these panels?

I just went into a super market and found a room full of these still in use.

[Linked Image]

[Linked Image]

Bob


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#152307 07/06/04 11:30 AM
Joined: Nov 2001
Posts: 745
M
Member
Hi Bob:
I have one of these Frank Adam panels (a smaller one, fortunately - 20 circuits, 120-240 volt single phase) in my collection of vintage electrical equipment. It was given to me by a friend on the occasion of demolition of an old country club building. A couple of the fuse sockets were nearly incinerated from the intense heat of overfusing/overloading for many years. I remember doing sound jobs in this old building and having to replace a burned out fuse every once in a while. You could literally feel the heat radiating out of this panel while standing four feet in front of it (even worse when the door was open... [Linked Image] ). I'm amazed that there were never any fires resulting from the bad wiring in this place.

Aside from being deadly, the panel shown in your picture is a fascinating piece. Looks like 30 circuits distributed over three phases, with very small feeder conductors at that. Wonder what all the contactors at the bottom are for? The bussing arrangement beneath the fuse sections would be interesting to examine.

Are any of these panels labelled as to purpose/use? What kind of MDP is in use here?

I recently purchased a panel like this, made by Bulldog Electric Products Corp. These things, if given reasonably good care, were made to last to the end of time!

A very interesting picture!! Thanks for sharing it. [Linked Image]

Mike (mamills)

[This message has been edited by mamills (edited 07-06-2004).]

#152308 07/06/04 05:03 PM
Joined: Oct 2000
Posts: 5,392
S
Member
I can recall punting a few of the single ph residential types in the dumpster in the past.

If memory serves, the switches simply defeated the fuses for no-load replacement

probably an archivist would be somewhat bothered by cavalier 'tude to some of these old gems

but imho, Frank should have stayed with the family brewery...
[Linked Image from riverviewendo.com.au]

#152309 07/07/04 05:59 PM
Joined: Jan 2003
Posts: 4,391
I
iwire Offline OP
Moderator
It's funny I thought of Sam Adams also. [Linked Image]

Thanks Mike, It must be a design in these panels as I could feel the heat radiating off of the panels too.

If I remember all the equipment was Frank Adams including the service switch and a large fused switch panel with 100 and 200 amp positions.

Bob


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#152310 07/07/04 06:54 PM
Joined: Jan 2002
Posts: 1,457
E
Member
I did some work in one of the Hospitals in Boston about 10 years ago. The panels were all Frank Adams. No fuses just curcuit breakers. I wish I had pictures. I remember them being a very odd design and the breakers verry expensive.

#152311 07/10/04 03:32 AM
Joined: Feb 2004
Posts: 1,438
Member
Ive never come across one of these here in CA.. I saw one once in in a major department store in NYC while I lived over there... Dead of winter, maybe it was the heat that drew my attention towards it [Linked Image]

-Randy

PS... Speaking of heat, the fuse in Ckt #20's place looks like it's seen some!

#152312 08/15/04 10:18 PM
Joined: Oct 2000
Posts: 4,116
Likes: 4
Member
FYI,

I just got an Email from a relative (of Frank Adam) saying hello, and that Frank Adam is now 92 and living in St. Louis.

[Linked Image]
Bill

[This message has been edited by Bill Addiss (edited 08-15-2004).]


Bill
#152313 08/16/04 07:36 PM
Joined: Jun 2003
Posts: 681
P
Member
Bill
That is pretty cool!
I have asked the guys around here to keep the weird things that they take apart or demo, I like to use them in class. About two months ago, a contractor brought me a Frank Adams panel he demoed, said he took his time and did it neat for me.
Sam Adams happens to be my favorite beer [Linked Image]!!

Pierre


Pierre Belarge
#152314 08/17/04 03:39 AM
Joined: Jan 2003
Posts: 4,391
I
iwire Offline OP
Moderator
Pierre the panels pictured are very close to you, Tarrytown, right on Rt 9. [Linked Image]

Perhaps a common panel for that area. [Linked Image]

Bob


Bob Badger
Construction & Maintenance Electrician
Massachusetts
#152315 08/17/04 12:26 PM
Joined: Apr 2002
Posts: 2,527
B
Moderator
About 20 years ago, Frank Adam produced three-pole NEMA-3R 30- and 60-amp 250V “pullout” air-conditioner disconnects. Their 3-pole version seemed unique—and included all-copper current-carrying parts, and were about ¼ the price of a traditional equivalent-rated “XOP” disconnect switch.


Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5