ECN Electrical Forum - Discussion Forums for Electricians, Inspectors and Related Professionals
ECN Shout Chat
ShoutChat
Recent Posts
Increasing demand factors in residential
by gfretwell - 03/28/24 12:43 AM
Portable generator question
by Steve Miller - 03/19/24 08:50 PM
Do we need grounding?
by NORCAL - 03/19/24 05:11 PM
240V only in a home and NEC?
by dsk - 03/19/24 06:33 AM
Cordless Tools: The Obvious Question
by renosteinke - 03/14/24 08:05 PM
New in the Gallery:
This is a new one
This is a new one
by timmp, September 24
Few pics I found
Few pics I found
by timmp, August 15
Who's Online Now
1 members (CoolWill), 250 guests, and 13 robots.
Key: Admin, Global Mod, Mod
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
#1291 05/06/01 02:43 PM
Joined: Jan 2001
Posts: 1,044
Tom Offline OP
Member
What's your favorite tool that is best known for it's use in another trade?

For example, my favorite non-electricians tool is the C-grip which is usually used by welders. It uses the vise grip action but instead of a pleirs end, it forms a big C. They're great for holding a panelboard in place while you reach for the screws & your cordless screwdriver. Also handy for holding conduit to beams & girts while you dig around for a strap. I refer to my pair as my third hand.

Tom


Few things are harder to put up with than the annoyance of a good example.
#1292 05/06/01 06:34 PM
Joined: Apr 2001
Posts: 449
F
Member
I have a cheap 4x4 remote control toy monster truck. It was the result of a brainstorm when I was pulling several runs of Cat5 cable in a drop ceiling in a large office. Just tie the cable to the roll bar, stand on a ladder with my head above the grid ceiling and drive the truck to the desired location. It climbs right over lay-in fixtures and other cables. Once you get to where you're going, just move the ladder to retrieve the truck and fish the cable down the wall. The truck even has headlights!
I had a hard time convincing my kids it wasn't a toy!

#1293 05/07/01 11:21 AM
Joined: Nov 2000
Posts: 2,236
Likes: 1
Member
RC... That's very cool!

I fly RC, but I've never actually used it for work in any way. I've got a truck too, and I'll keep that idea in mind if the situation ever occurs for me. The slower Radio Shack 4x4 models would work great!
www.kellyelectric.electrical-contractor.net/Planes/Plane.htm shows some of my aviation exploits including some aerial photography via RC.


[This message has been edited by sparky66wv (edited 05-07-2001).]


-Virgil
Residential/Commercial Inspector
5 Star Inspections
Member IAEI
#1294 05/07/01 11:57 AM
Joined: Nov 2000
Posts: 2,148
R
Member
Quote
Just tie the cable to the roll bar, stand on a ladder with my head above the grid ceiling and drive the truck to the desired location. It climbs right over lay-in fixtures and other cables.

Fred,
Cat-5 cable is to be kept 12" away from light fixtures.
Don(resqcapt19)

[This message has been edited by resqcapt19 (edited 05-07-2001).]


Don(resqcapt19)
#1295 05/07/01 06:43 PM
Joined: Apr 2001
Posts: 449
F
Member
Don,
I know and I do. I was just saying that the truck can over-come most obstacles found in a grid ceiling. The network engineer at these offices provides the Cat5 cable and it is usually shielded/plenum cable wether it is required or not. None of these ceilings have been plenums so far. We stay away from the lights anyway.

#1296 05/07/01 07:13 PM
Joined: Oct 2000
Posts: 5,392
S
Member
i have an AM/FM circuit tracer, the other trades simply call it a 'radio'
[Linked Image]

#1297 05/09/01 10:05 AM
Joined: Apr 2001
Posts: 53
S
Member
[QUOTE]Originally posted by Fred:
[B]I have a cheap 4x4 remote control toy monster truck. It was the result of a brainstorm when I was pulling several runs of Cat5 cable in a drop ceiling in a large office.

Best idea that I've heard in a long time...... [Linked Image]

#1298 05/09/01 10:13 AM
Joined: Apr 2001
Posts: 53
S
Member
I like the little "A" clamps that most carpenters use on their "plumb bobs". I do keep a plumb bob in my bag. I can't tell you the number of times that I have laid out fixtures on the ground, and used a plumb bob to transpose the locations up to the ceiling.

#1299 05/09/01 10:38 AM
Joined: Nov 2000
Posts: 2,236
Likes: 1
Member
Yeah, I'm a plumb-bob user too. Especially when installing vertical runs of pipe, masts etc.


-Virgil
Residential/Commercial Inspector
5 Star Inspections
Member IAEI
#1300 05/09/01 03:21 PM
Joined: Oct 2000
Posts: 5,392
S
Member
I have a 'rasp', a heavy file i use for pvc

Page 1 of 3 1 2 3

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5